Need help?Do you have a question about the Stihl MS 650 and is the answer not in the manual?
General| Chain Oil Automatic | Yes |
|---|---|
| Chain Pitch | 3/8" |
| Sound Pressure Level | 106 dB(A) |
| Weight (without cutting equipment) | 7.3 kg |
| Fuel Tank Volume | 825 ml |
| Oil Tank Volume | 360 ml |
Detailed technical specifications for the engine.
Specifications related to the fuel delivery system.
Technical data for the ignition components.
Specifications for the automatic chain oiling system.
Specified torque values for various fasteners and components.
Diagnosing and resolving issues with clutch, chain, and brake.
Troubleshooting common problems with the starter rope mechanism.
Diagnosing and fixing problems with the chain oiling system.
Troubleshooting ignition system faults causing no-start or misfires.
Diagnosing and rectifying issues with engine idling and acceleration.
Troubleshooting general engine performance problems.
Procedure for removing and inspecting the clutch drum and sprocket.
Steps for removing and installing the chain catcher assembly.
Procedure for replacing the spiked bumper component.
Detailed steps for disassembling and assembling the clutch.
Instructions for checking and removing the chain brake mechanism.
Procedure for removing and installing the chain tensioning mechanism.
Steps for removing and installing the bar mounting studs.
How to remove, clean, or replace the muffler and spark arresting screen.
Procedure for removing and installing the engine shroud.
Methods for testing crankcase for air leaks using vacuum and pressure.
Instructions for removing and installing oil seals on the crankshaft.
Detailed steps for removing and installing the cylinder and piston assembly.
Procedure for removing, cleaning, and installing piston rings.
Steps for separating the crankcase and removing the crankshaft.
Procedure for removing and installing the decompression valve.
Description of the ignition module and its electrical connections.
Information on ignition timing being fixed and non-adjustable.
Procedure for removing and installing the engine flywheel.
Instructions for removing and installing the contact spring.
Steps for testing the wiring harness resistance and continuity.
Flowchart for diagnosing ignition system faults.
General information about the rewind starter mechanism.
Step-by-step guide for removing and installing the rewind starter.
Procedure for removing and installing the starter pawls.
Instructions for removing and installing the starter rope rotor.
Procedure for replacing the starter rope and grip assembly.
Steps for correctly tensioning the rewind spring.
Procedure for removing and installing the starter segment.
Instructions for replacing the starter rope guide bushing.
Detailed steps for safely replacing the rewind spring.
Procedure for removing and installing vibration damping buffers.
Instructions for removing and installing annular buffers on the tank housing.
Procedure for removing and installing the switch shaft.
Steps for removing and installing the throttle trigger and interlock lever.
Procedure for removing and installing the front handle assembly.
Instructions for removing and cleaning the oil pickup body and suction hose.
Procedure for cleaning and replacing the oil tank valve.
Detailed steps for removing, installing, and servicing the oil pump.
Instructions for cleaning and replacing the air filter element.
Procedure for removing and installing the carburetor unit.
Detailed steps for servicing internal carburetor components.
Guidance on adjusting carburetor settings for optimal performance.
Procedure for performing the basic setting on carburetors with limiter caps.
Instructions for checking and cleaning the fuel tank vent.
Information on the pickup body's function and cleaning the fuel tank.
Procedure for removing and replacing the fuel hose.
Instructions for removing and installing the fuel hose within the tank.
Steps for safely separating the crankcase from the tank housing.
Procedure for removing and installing the tank housing.
Tests for checking the generator, heating element, and thermostatic switch.
Flowchart for diagnosing faults in the carburetor heating system.
Troubleshooting guide for failures in the handle heating system.
Procedure for removing and installing the heater switch.
Instructions for replacing the heating element in the rear handle.
Information on the front handle heating element and replacement.
Procedure for inspecting and installing the generator unit.
Steps for removing and positioning the standard wiring harness.
Instructions for handling the wiring harness for heated components.
To Next Page
