Chapter 2: Installation
2-9
DIMM Installation
1. Insert the desired number of
DIMMs into the memory slots,
starting with DIMM1A, DIMM(see
the next page for the location). For
best performance, please use the
memory modules of the same type
and speed in the same bank.
2. Push the release tabs outwards
on both ends of the DIMM slot to
unlock it.
Release Tabs
Notches
3. Align the key of the DIMM mod-
ule with the receptive point on the
memory slot.
Press both notches
straight down into
the memory slot.
4. Align the notches on both ends of
the module against the receptive
points on the ends of the slot.
5. Use two thumbs together to press
the notches on both ends of the
module straight down into the slot
until the module snaps into place.
6. Press the release tabs to the lock
positions to secure the DIMM module
into the slot.
Removing Memory Modules
Reverse the steps above to remove the
DIMM modules from the motherboard.
2-3 Installing DDR3 Memory
Note: Check the Supermicro website for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
4
DIMM_D2
DIMM_B2
DIMM_A2
DIMM_B1
DIMM_A1
DIMM_D1 DIMM_C2 DIMM_C1
SAS CODE
A
JIPMB1
4
US1
JS5
4
1
1
JS7
16
2
1
JS6
13
22
7
1
JLAN2
6
1
JLAN1
JRK1
1
1
JD1
7
JPW2
UID_SW
1
JF1
19
20
1
JTAG1
UID_LED
A
C
X_BT1
+
JPI2C1
JBT1
JPW1
6-SGPIO2
7
2
1
6-SGPIO1
7
T-SGPIO1
8
2
7
T-SGPIO2
1
8
JWOR1
1
JL1
JOH1
JI2C2
1
JI2C1
1
DP3
A
C
CA
JPS1
1
JPL2
13
JPME2
1
3
3
1
JS4
3
1
JRK3
3
1
JRK2
JPME1
3
1
JVR1
1
3
1
JPUSB1
JPL1
1
3
3
1
JPB1
JVI2C2
1
3
JVI2C1
1
3
1
3
JWD1
JVR2
3
1
JPG1
4
1
FAN1
4
FAN4
1
4
1
FANA
FAN3
1
FAN2
4
MH1
MH9
MH11
MH5
MH7
MH8
MH10
C361
20
2
JTPM1
1
1
3
JSD1
JSTBY1
1
3
9
6
5
1
JCOM2
1
2
7
1
7
2
1
7
2
10
JF1
IPMI_LAN
1-2 Enable
2-3 Disable
JPS1
/CPU1
SLOT4 PCI33MHZ
SLOT2 PCI33MHZ
1-2:NORMAL
JPME1
2-3:ME RECOVERY
USB2/3
USB6/7
USB4/5
USB8
P1-DIMMD2
P1-DIMMC2
P1-DIMMC1
P1-DIMMD1
P1-DIMMB2
P1-DIMMA2
CPU1
SLOT6 PCI-E 3.0 X16
SLOT3 PCI-E 3.0 X8 (IN X16)
SLOT1 PCI33MHZ
JBT1 COMS CLEAR
JPME2
JPI2C1:PWRI2C
JTPM1:TPM/PORT80
COM2
RAID_KEY(Intel)
JPB1
1-2 Enable
2-3 Disable
1-2:NORMAL
2-3:ME MANUFACTURING MODE
1-2 Enable
2-3 Disable
JPG1: VGA
OFF:DISABLE
JI2C1/JI2C2
ON: ENABLE
UID
RST
ON
PWR
LAN2
PWR
FF
OH
FAIL
HDD
LED
PWR
X
NIC
1
2
NIC
NMI
LAN1
2-3:NMI
1-2:RST
2-3 Disable
1-2 Enable
JWD1:Watch Dog
JPL1/2: LAN
PWR LED
SPEAKER
1-3:
4-7:
JD1:
VGA
COM1
USB0/1
2-3 Disable
P1-DIMMB1
KB/MOUSE
1-2 Enable
JPUSB1:USB0/1 Wake Up
P1-DIMMA1
CLOSE 1st
OPEN 1st
2
7
2
1
Socket R
LGA 2011
CPU
SLOT5 PCI-E 2.0 X4 (IN X8)
To Next Page
Loading...
