Supermicro Supero X9SRH-7F - BMC Enable;Disable (JPB1); USB Wake-Up (JPUSB1)

Chapter 2: Installation
2-35
4
DIMM_D2
DIMM_B2
DIMM_A2
DIMM_B1
DIMM_A1
DIMM_D1 DIMM_C2 DIMM_C1
SAS CODE
A
JIPMB1
4
US1
JS5
4
1
1
JS7
16
2
1
JS6
13
22
7
1
JLAN2
6
1
JLAN1
JRK1
1
1
JD1
7
JPW2
UID_SW
1
JF1
19
20
1
JTAG1
UID_LED
A
C
X_BT1
+
JPI2C1
JBT1
JPW1
6-SGPIO2
7
2
1
6-SGPIO1
7
T-SGPIO1
8
2
7
T-SGPIO2
1
8
JWOR1
1
JL1
JOH1
JI2C2 1
JI2C1
1
DP3
A
C
CA
JPS1
1
JPL2
13
JPME2
1
3
3
1
JS4
3
1
JRK3
3
1
JRK2 JPME1
3
1
JVR1
1
3
1
JPUSB1
JPL1
1
3
3
1
JPB1
JVI2C2
1
3
JVI2C1
1
3
1
3
JWD1
JVR2
3
1
JPG1
4
1
FAN1
4
FAN4
1
4
1
FANA
FAN3
1
FAN2
4
MH1
MH9
MH11
MH5
MH7
MH8
MH10
C361
20
2
JTPM1
1
1
3
JSD1
JSTBY1
1
3
9
6
5
1
JCOM2
1
2
7
1
7
2
1
7
2
10
JF1
IPMI_LAN
1-2 Enable 2-3 Disable JPS1
/CPU1
SLOT4 PCI33MHZ
SLOT2 PCI33MHZ
1-2:NORMAL
JPME1
2-3:ME RECOVERY
USB2/3
USB6/7
USB4/5
USB8
P1-DIMMD2 P1-DIMMC2 P1-DIMMC1 P1-DIMMD1
P1-DIMMB2 P1-DIMMA2
CPU1
SLOT6 PCI-E 3.0 X16
SLOT3 PCI-E 3.0 X8 (IN X16)
SLOT1 PCI33MHZ
JBT1 COMS CLEAR
JPME2
JPI2C1:PWRI2C
JTPM1:TPM/PORT80
COM2
RAID_KEY(Intel)
JPB1
1-2 Enable
2-3 Disable
1-2:NORMAL 2-3:ME MANUFACTURING MODE
1-2 Enable 2-3 Disable JPG1: VGA
OFF:DISABLE
JI2C1/JI2C2
ON: ENABLE
UID
RST
ON
PWR
LAN2
PWR
FF OH
FAIL
HDD LED PWR
X
NIC
1 2
NIC
NMI
LAN1
2-3:NMI
1-2:RST
2-3 Disable
1-2 Enable
JWD1:Watch Dog
JPL1/2: LAN
PWR LED
SPEAKER
1-3:
4-7:
JD1:
VGA
COM1
USB0/1
2-3 Disable
P1-DIMMB1
KB/MOUSE
1-2 Enable
JPUSB1:USB0/1 Wake Up
P1-DIMMA1
CLOSE 1st
OPEN 1st
2
7
2
1
Socket R
LGA 2011
CPU
SLOT5 PCI-E 2.0 X4 (IN X8)
A
A. USB 0/1 Wake-up
B. BMC Enable/Disable
USB Wake-Up (JPUSB1)
Use the jumper JPUSB1 to "wake-up"
your system by pressing a key on a USB
keyboard or clicking the USB mouse con-
nected to the backpanel USB Ports 0/1.
JPUSB1 is used together with a USB
Wake-Up feature in the BIOS. Enable this
jumper and the USB support in the BIOS to
wake up your system via USB devices.
Note: When the USB is set to Enabled
in the BIOS, and JPUSB1 is set to Dis-
abled, remove the USB devices from
Backplane USB Ports 0/1 before the
system goes into the standby mode.
USB 0/1 Wake-up Enable
Jumper Settings
Pin#Denition
1-2 Enabled (Default)
2-3 Disabled
B
BMC Enable/Disable (JPB1)
JPB1 is used to enable or disable the
BMC (Baseboard Management Control)
chip and the onboard IPMI connection.
This jumper is used together with the IPMI
settings in the BIOS. See the table on the
right for jumper settings.
BMC IPMI Enable/Disable
Jumper Settings
SettingsDenition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled