EasyManuals Logo

Supermicro X11DPG-QT User Manual

Supermicro X11DPG-QT
259 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #99 background imageLoading...
Page #99 background image
Chapter 4: UEFI BIOS
99
*If the feature, Congure sSATA as, is set to AHCI, the following features will become
available for user's conguration:
sSATA Port 0~ Port 5
This feature displays the information detected on the installed SATA drive on the particular
SATA port.
Model number of drive and capacity
Software Preserve Support
Hot Plug (sSATA Port 0~ Port 5)
Select Enabled to enable a SATA port specied by the user. The options are Disable and
Enable.
Spin Up Device (sSATA Port 0~ Port 5)
On an edge detect from 0 to 1, set this feature to allow the PCH to initialize the device.
The options are Disable and Enable.
sSATA Device Type (sSATA Port 0~ Port 5)
Use this feature to specify if the SATA port specied by the user should be connected to a
Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive and Solid State
Drive.
*If the feature, Congure SATA as, is set to RAID, the following features will become
available for user's conguration:
sSATA RSTe Boot Info
Select Enable to provide the full int13h support for SATA controller attached devices. The
options are Disable and Enable.
sSATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy driver for
system boot. The options are Disable, EFI, and Legacy.
sSATA Port 0~ Port 5
This feature displays the information detected on the installed SATA drive on the particular
SATA port.
Model number of drive and capacity
Software Preserve Support
Hot Plug (sSATA Port 0~ Port 5)
Select Enabled to enable a SATA port specied by the user. The options are Disable and
Enable.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Supermicro X11DPG-QT and is the answer not in the manual?

Supermicro X11DPG-QT Specifications

General IconGeneral
PS/2 ports quantity0
IPMI LAN (RJ-45) portYes
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity2
Number of SATA III connectors10
Number of DIMM slots16
Maximum LRDIMM memory2000 GB
Supported RDIMM module capacity64GB
Memory voltage1.2 V
Supported memory typesDDR4-SDRAM
Supported memory clock speeds2133, 2400, 2666 MHz
BIOS typeAMI
ACPI version4.0
BIOS memory size64 Mbit
RAID levels0, 1, 5, 10
Wi-FiNo
LAN controllerIntel® X550
Ethernet interface type10 Gigabit Ethernet
On-board graphics card modelAspeed AST2500
Bundled softwareIntel Node Manager, IPMI2.0, KVM LAN, NMI, SPM, SSM, SUM, SuperDoctor 5, Watchdog
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)10 - 35 °C
Storage relative humidity (H-H)5 - 95 %
Operating relative humidity (H-H)8 - 90 %
Supported QPI10.4 GT/s
Processor socketLGA 3647 (Socket P)
Processor manufacturerIntel
Processor number of cores supported28
Component forServer
Motherboard chipsetIntel® C621
Audio output channels7.1 channels
PCI Express x16 (Gen 3.x) slots6
Weight and Dimensions IconWeight and Dimensions
Depth335.3 mm
Width384 mm

Related product manuals