Telegesis ETRX357-LR - User Manual

Telegesis
TG-ETRXn-R309-AT-Commands
ETRX3 series
AT-Command Dictionary 3.09
©2015 Telegesis (UK) Ltd AT Command Manual July 2015 (Rev 3.09)
ETRX3 Series ZigBee Module
AT-Command Dictionary
Firmware R309
EmberZNet 5.4.0 stack

Summary

1 Introduction

1.1 The first step

Guide to finding firmware version via AT command.

1.2 Module overview

Describes AT-Command interface for ETRX3 series ZigBee PRO modules.

1.3 Document Overview

Reference for AT-Command and S-Register for R3xx revisions.

1.4 Network topology

Describes ZigBee network topology with Coordinator, Routers, and End Devices.

1.5 The ADCs

Details the Analog-to-Digital Converters (ADCs) on the ETRX357.

1.6 RTC Related Commands

Discusses Real-Time Clock (RTC) commands and synchronization.

1.7 A Note on ZigBee Compliance

Covers Telegesis R300 firmware's ZigBee Alliance certification.

1.8 Important notes

Contains critical information regarding hardware, bootloader, compatibility, and parameters.

2 AT Style Command Conventions

2.1 Parameters

Defines different formats for AT command parameters like XX, XXXX, PID, etc.

2.2 Prompt Overview

Lists and explains various prompts that can appear during ETRX357 module operation.

2.3 Device Overview

Provides an overview of ZigBee device types (COO, FFD, ZED, SED, MED) and non-ZigBee types (Sink).

2.4 Addressing modes

Explains different formats for device addresses like EUI64 and Network address.

2.5 AT Command Overview

Provides a quick reference table of all available AT commands categorized by function.

2.6 Module Control & Configuration Commands

Details commands for controlling and configuring the module's hardware and settings.

2.7 Network Control & Configuration Commands

Covers commands for establishing and managing ZigBee networks and device connections.

2.8 Messaging

Explains commands for sending and receiving various types of ZigBee messages.

2.9 Binding Management (ETRX3 Series only)

Manages ZigBee binding table entries for device communication.

2.10 Time-related commands

Commands for setting, getting, and synchronizing the module's local time.

3 List of Error codes

4 S-Registers

4.1 Recovery of the Factory Default Settings

Procedure to reset the module to factory default settings when unresponsive.

4.2 S-Registers for Network Setup

Details S-registers related to network configuration like channel mask and PAN ID.

4.3 S-Registers for Module Setup

Covers S-registers that define module behavior like device type and security settings.

4.4 I;O related S-Registers

Describes S-registers for configuring UART setup and I/O pin functionalities.

4.5 S-Registers Defining the Functionality of the Module

Explains S-registers that define module actions based on events like interrupts or timers.

4.6 Advanced Settings

Covers S-registers for advanced configurations like multicast table entries and profile IDs.

5 Build in Functionality

6 ETRX357 Power Consumption (Provisional data)

7 Notes on Energy Levels and LQI

7.1 Interpreting LQI

Explains how to interpret Link Quality Indicator (LQI) and its relation to SNR.

7.2 Interpreting RSSI Energy Levels

Describes how to interpret Received Signal Strength Indicator (RSSI) energy levels.

8 Trademarks

9 Disclaimer

10 Contact Information

11 References

12 Appendix A. Forming a secure network

13 Appendix B. Bootloading new firmware

13.1 Bootloading through the serial port

Details the process of bootloading firmware via the serial port using the bootloader menu.

13.2 Bootloading over the air

Explains bootloading firmware to remote nodes using AT+PASSTHROUGH.

Telegesis ETRX357-LR Specifications

General

Brand	Telegesis
Model	ETRX357-LR
Category	Control Unit
Language	English