VTAŽENÍ SPODNÍ NITĚ
TABULKA MATERIÁLŮ, NITÍ A JEHELT
Zdvihněte přítlačnou patku
1. Levou rukou lehce přidržujte nit, otáčejte ručním kolem směrem k sobě a
spouštějte jehlu a pokračujte, dokud se jehla nedostane znovu do nejvyšší polohy
nebo stiskněte tlačítko polohy jehly nahoře/dole.
2. Lehce zatáhněte za horní nit. Spodní nit zformuje pod patkou smyčku.
3. Vytáhněte asi 10 cm obou nití dozadu pod patkou
Zvolte sílu nitě i správnou jehlu dle následující tabulky
Nezapomeňte vždy použít správnou jehlu pro určitý materiál.
9
KNOWING YOUR SEWING MACHINE
Balancing top thread tension
The top thread and the bobbin thread
should interlock in the center of two layers
of fabric in straight seams.
Set the desired number of the thread
tension dial at setting mark.
Loosen the needle thread tension by
moving the dial to a lower number.
Tighten the needle thread tension by
moving the dial to a higher number.
NOTE: In order to obtain better zigzag stitches, the top thread tension should be
slightly weaker than the bobbin thread tension. That means, the top thread
should appear slightly on the reverse side of the fabric, but the bobbin thread
c
annot appear on the top side of the fabric.
Drawing up bobbin thread
Raise the presser foot and hold the needle thread lightly
with you left hand.
Turn the hand wheel slowly towards you with your right
hand until the needle goes down and continue turning the
hand wheel until the take-up lever is at its highest
position.
Lightly draw up the needle thread forming a loop of the
bobbin thread.
Pull 15cm (6 inches) of both thread back and under the
presser foot.
③
②
9
KNOWING YOUR SEWING MACHINE
Balancing top thread tension
The top thread and the bobbin thread
should interlock in the center of two layers
of fabric in straight seams.
Set the desired number of the thread
tension dial at setting mark.
Loosen the needle thread tension by
moving the dial to a lower number.
Tighten the needle thread tension by
moving the dial to a higher number.
NOTE: In order to obtain better zigzag stitches, the top thread tension should be
slightly weaker than the bobbin thread tension. That means, the top thread
should appear slightly on the reverse side of the fabric, but the bobbin thread
c
annot appear on the top side of the fabric.
Drawing up bobbin thread
Raise the presser foot and hold the needle thread lightly
with you left hand.
Turn the hand wheel slowly towards you with your right
hand until the needle goes down and continue turning the
hand wheel until the take-up lever is at its highest
position.
Lightly draw up the needle thread forming a loop of the
bobbin thread.
Pull 15cm (6 inches) of both thread back and under the
presser foot.
③
②
9
KNOWING YOUR SEWING MACHINE
Balancing top thread tension
The top thread and the bobbin thread
should interlock in the center of two layers
of fabric in straight seams.
Set the desired number of the thread
tension dial at setting mark.
Loosen the needle thread tension by
moving the dial to a lower number.
Tighten the needle thread tension by
moving the dial to a higher number.
NOTE: In order to obtain better zigzag stitches, the top thread tension should be
slightly weaker than the bobbin thread tension. That means, the top thread
should appear slightly on the reverse side of the fabric, but the bobbin thread
c
annot appear on the top side of the fabric.
Drawing up bobbin thread
Raise the presser foot and hold the needle thread lightly
with you left hand.
Turn the hand wheel slowly towards you with your right
hand until the needle goes down and continue turning the
hand wheel until the take-up lever is at its highest
position.
Lightly draw up the needle thread forming a loop of the
bobbin thread.
Pull 15cm (6 inches) of both thread back and under the
presser foot.
③
Typ látky Síla ni Síla jehly
Lehký materiál
Bavlna #120 - 150
Hedvábí #120 - 150
PES #120 - 150
70 – 80
Střední materiál
Bavlna #100 - 120
Hedvábí #100 – 120
PES #100 - 120
80 – 90
Těžký materiál
Bavlna #50 - 80
Hedvábí #50 - 80
PES #50 - 80
90 – 100
Streč, dvojitý úplet, trikot,
spandex, jersey
Ctn. #120 - 150 80 – 90
Texi Fox 2516
CS
Texi Fox 25 INSTRUKCJA 2019.indb 16 17.09.2019 12:15
To Next Page
Loading...
Need help?
General
