THUNDER TIGER raptor e700 - Main Frame Assembly

-8-
Tail Boom Bracket Assembly / 尾管固定座組裝
No.
1
2
3
3-1
3-2
3-3
4
5
6
7
8
QtyDescription 名稱
機身尾管固定座(右)
機身尾管固定座(左)
驅動傘齒軸套組
驅動傘齒軸套
滾珠軸承
, d12xD18xW4
傘齒軸環 , d12xD13xW6.85
尾螺旋傘齒輪A(24T)
尾螺旋傘齒輪B(24T)
尾驅動齒輪軸
尾驅動齒輪26T
固定銷
, ∅2x12
TAIL BOOM BRACKET-R
TAIL BOOM BRACKET-L
BEVEL SHELL SET
BEVEL SHELL
BEARING, d12xD18xW4
BEVEL COLLAR, d12xD13xW6.85
TAIL DRIVE BEVEL GEAR-A (24T)
TAIL DRIVE BEVEL GEAR-B (24T)
TAIL DRIVE GEAR SHAFT
TAIL DRIVE GEAR-26T
PIN, ∅2x12
1
1
1
1
2
1
1
1
1
1
2
No.
9
10
11
12
13
14
15
16
17
18
QtyDescription
名稱
滾珠軸承, d5xD11xW5
無頭內六角螺絲, M3x4
側板支柱
伺服機後置固定板
內六角螺絲, M3x22
內六角螺絲, M3x16
內六角螺絲, M3x10
止鬆螺帽, M3
墊片, d12xD14.5xW0.2
墊圈, d3xD8xW1.4
BEARING, d5xD11xW5
SET SCREW, M3x4
FRAME SPACER
REAR SERVO FRAME
SOCKET SCREW, M3x22
SOCKET SCREW, M3x16
SOCKET SCREW, M3x10
LOCK NUT, M3
WASHER, d12xD14.5xW0.2
WASHER, d3xD8xW1.4
2
2
4
1
2
2
2
6
1
2
Apply threadlocker
使用螺絲防鬆膠
Bag B
(2)
(3)
(1)
(16)
(16)
(11)
(12)
(15)
(18)
(18)
(14)
(14)
(13)
Assemble the Tail Boom Bracket as
drawing. Secure the Screws but do
not tighten at this step.
參考圖示組裝尾管固定座，螺絲只需
稍事固定，暫無需鎖緊。
SOCKET SCREW, M3x16
內六角螺絲, M3x16
SOCKET SCREW, M3x10
內六角螺絲, M3x10
LOCK NUT, M3
止鬆螺帽, M3
BEVEL COLLAR, d12xD13xW6.85
傘齒軸環 , d12xD13xW6.85
BEARING, d12xD18xW4
滾珠軸承, d12xD18xW4
BEARING, d5xD11xW5
滾珠軸承, d5xD11xW5
PIN, ∅2x12
固定銷, ∅2x12
SET SCREW, M3x4
無頭內六角螺絲, M3x4
SOCKET SCREW, M3x22
內六角螺絲, M3x22
WASHER, d12xD14.5xW0.2
墊片 , d12xD14.5xW0.2
(6)
(7)
(5)
T22
T22
(10)
(10)
(9)
(9)
(8)
(8)
(3-2)
(3-1)
(3-3)
(3-2)
(17)
(4)
Check the mesh of gears (#4 & #5),
please add the washer (#17) for a
proper mesh if too much play.
請檢查齒輪間隙(#4及#5)，間隙過大時
請酌加墊片(#17)。
WASHER, d3xD8xW1.4
墊圈, d3xD8xW1.4