THUNDER TIGER raptor e700 - Tail Rotor System Assembly

-15-
1. Note the orientation of the Thrust Bearings; please refer
page 6, Diagram for Thrust Bearing Assembly.
2. Line up the concave of Tail Rotor Shaft and the hole of Hub
when securing the Tail Rotor Hub onto the Tail Rotor Shaft.
1. 請參考第 6 頁止推軸承安裝示意圖，注意安裝方向性。
2. 將尾旋翼固定座鎖上尾旋翼主軸時，請注意軸上凹槽需對正固定
座上螺絲孔。
METAL TAIL GRIP
WASHER, d7.5xD10xW0.3
WASHER, d5xD7.5xW0.3
THRUST BEARING, d5xD10xW4
BEARING, d5xD10xW4
TAIL ROTOR HUB
SET SCREW, M3x3
WASHER, d3xD7xW0.5
TORX SCREW, M3x8
TAIL PITCH CONTROL LINK
2
2
2
2
4
1
2
2
2
2
No.
1
2
3
4
5
6
7
8
9
10
QtyDescription 名稱
金屬尾旋翼轉座
墊片
, d7.5xD10xW0.3
墊片 , d5xD7.5xW0.3
止推軸承 , d5xD10xW4
滾珠軸承, d5xD10xW4
尾旋翼座
無頭內六角螺絲, M3x3
墊圈
, d3xD7xW0.5
星型低頭螺絲, M3x8
尾旋翼連接頭
SOCKET SCREW, M2x8
COLLAR, d2xD3xW4.2
PIN, ∅2 x19
E-CLIP, #1.5
TAIL ROTOR SHAFT
TAIL PITCH CONTROL FORK
TAIL PITCH SLIDER
BEARING, d6xD10xW3
TAIL PITCH SLIDER BUSHING
LINKAGE BALL(B)
2
2
2
2
1
1
1
2
1
1
No.
11
12
13
14
15
16
17
18
19
20
QtyDescription 名稱
內六角螺絲, M2x8
軸環
, d2xD3xW4.2
固定銷 , ∅2 x19
E型扣環 , #1.5
尾旋翼軸
尾旋翼控制座
尾旋翼滑座
滾珠軸承, d6xD10xW3
尾旋翼控制軸套
內六角連接頭自攻螺絲(B)
(13)
(7)
(7)
(11)
(12)
(14)
(10)
(6)
(1)
(5)
(2)
(4)
(3)
(8)
(9)
(18)
(18)
(17)
(20)
(19)
(15)
(16)
Secure all screws shown on this page with a drop of threadlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
Tail Rotor System / 尾旋翼機構組裝
Apply threadlocker
使用螺絲防鬆膠
(5)
Bag G
WASHER, d7.5xD10xW0.3
墊片 , d7.5xD10xW0.3
WASHER, d5xD7.5xW0.3
墊片 , d5xD7.5xW0.3
THRUST BEARING, d5xD10xW4
止推軸承 , d5xD10xW4
BEARING, d5xD10xW4
滾珠軸承, d5xD10xW4
SOCKET SCREW, M2x8
內六角螺絲, M2x8
COLLAR, d2xD3xW4.2
軸環, d2xD3xW4.2
PIN, ∅2 x19
固定銷, ∅2 x19
E-CLIP, #1.5
E型扣環, #1.5
WASHER , d3xD7xW0.5
墊圈 , d3xD7xW0.5
SET SCREW, M3x3
無頭內六角螺絲, M3x3
TORX SCREW, M3x8
星型低頭螺絲, M3x8
LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
BEARING, d6xD10xW3
滾珠軸承, d6xD10xW3
Completed View
組裝完成
Assemble left and right
side the same way
左右側組件相同
Apply grease
使用潤滑油膏
Ensure smooth, non-binding
movement when assembling
確認組件靈活度