-7-
No.
15
16
17
18
19
20
21
22
23
24
25
26
26-1
26-2
QtyDescription
名稱
OUTER DAMPER
INNER DAMPER
SPINDLE
THRUST COLLAR, 0.5mm
THRUST COLLAR, 1mm
THRUST COLLAR, 0.2mm
THRUST COLLAR, 0.1mm
WASHER, d5xD11xW1.7
SOCKET SCREW, M5x10
FBL HEAD BUTTON
SOCKET SCREW, M2.5x6
LINKAGE ROD SET, 42.55mm
LINGAGE ROD
BALL LINK
外避震墊圈
內避震墊圈
固定軸
推力軸環, 0.5mm
推力軸環, 1mm
推力軸環, 0.2mm
推力軸環, 0.1mm
墊片, d5xD11xW1.7
內六角螺絲
, M5x10
無平衡翼煞車盤
內六角螺絲
, M2.5x6
連接桿組
, 42.55mm
連接桿
單頭連接桿
2
2
1
2
2
2
2
2
2
1
2
2
1
2
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
QtyDescription
名稱
HARDENED MAIN SHAFT(12mm)
SOCKET SCREW, M3x5
METAL SWASHPLATE
FBL CONTROL LEVER
BEARING, d4xD8xW3
COLLAR, d3xD4xW8.5
SOCKET SCREW, M3x14
WASHER, d3xD5xW0.5
LINKAGE BALL(A)
FBL WASHOUT LINKAGE
BEARING, d3xD6xW2.5
COLLAR, d2xD3xW3.4
BUTTON HEAD SOCKET SCREW, M2x8
FBL MAIN ROTOR HUB
強化主軸(12mm)
內六角螺絲
, M3x5
金屬十字盤
無平衡翼控制搖臂
滾珠軸承, d4xD8xW3
軸套,
d3xD4xW8.5
內六角螺絲
, M3x14
墊片, d3xD5xW0.5
內六角連接頭螺絲(A)
無平衡翼連接座
滾珠軸承,
d3xD6xW2.5
軸套,
d2xD3xW3.4
半圓頭內六角螺絲
,
M2x8
金屬主旋翼固定座
1
4
1
2
4
2
2
2
2
2
4
4
4
1
(24)
(25)
(26)
(26)
(14)
(13)
(16)
(17)
(15)
Main Rotor System & Linkage Rod /
主旋翼機構及連桿組裝
Bag A
(11)
(12)
(13)
(11)
(10)
(5)
(5)
(4)
(2)
(2)
(1)
(3)
(6)
(9)
(8)
(7)
(12)
(22)
(23)
(18~21)
SOCKET SCREW, M3x14
內六角螺絲
, M3x14
BEARING, d4xD8xW3
滾珠軸承
, d4xD8xW3
SOCKET SCREW, M3x5
內六角螺絲
, M3x5
COLLAR, d3xD4xW8.5
軸套
, d3xD4xW8.5
SOCKET SCREW,
M2.5x6
內六角螺絲,
M2.5x6
SOCKET SCREW,
M5x10
內六角螺絲,
M5x10
WASHER, d5xD11xW1.7
墊片, d5xD11xW1.7
LINKAGE BALL(A)
內六角連接頭螺絲(A)
WASHER
, d3xD5xW0.5
墊片
, d3xD5xW0.5
Secure all screws shown on this page
with a drop of threadlocker.
本頁顯示之螺絲請使用適量防鬆膠鎖固。
The holes should
point up.
有2孔的一端應朝上
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right
side the same way
左右側組件相同
Ensure smooth, non-binding
movement when assembling
確認組件靈活度
Apply grease
使用潤滑油膏
COLLAR
, d2xD3xW3.4
軸套
, d2xD3xW3.4
BEARING
, d3xD6xW2.5
滾珠軸承
, d3xD6xW2.5
BUTTON HEAD
SOCKET SCREW, M2X8
半圓頭內六角螺絲, M2X8
Rotate the Main Rotor
Grip to check if it runs
effortlessly and smoothly;
please reallocate the different
thickness of Thrust Collars for
getting a proper mesh if too much
play or over tight.
完成組裝後，請轉動主旋翼轉座確認
作動是否順暢；如間隙過大或過緊，
請更改不同厚度之推力軸環組合以獲
得適當間隙。
(1.0mm) (0.5mm) (0.2mm) (0.1mm)
d8xD12
42.55
24
Scale=1:1 (unit:mm)
x2
(26-1)
(26-2)
(26-2)
To Next Page
Loading...
