Topcon GPT-7003i - Function Key (Soft Key)

116 pages

To Next Page

To Previous Page

1 NOMENCLATURE AND FUNCTIONS

1.10 Function Key (Soft Key)

The functions are according to the displayed message.

Coordinate measuring mode (Page 1)

Angle measuring mode (Page 1)

Distance measuring mode (Page 1)

Angle measuring mode (Page 2)

Distance measuring mode (Page 2)

Coordinate measuring mode (Page 2)

Main Page

Foreword3
General Handling Precautions4
Display for Safe Use5
Safety Cautions5
Measurement Menu5
User7
Exceptions from Responsibility7
Laser Safety8
Labels8
Symbol Mark While the Laser Is Emitting8
Table of Contents9
Contents9
Standard Set Composition11
Nomenclature and Functions12
Nomenclature12
Display14
Main Menu Contains14
Display Marks15
Display Keys15
Shortcut Keys16
Backlight Adjustment17
How to Adjust Reducing Time of Backlight17
Adjust the Backlight Brightness by Manual19
Selecting the Automatic Lighting Option20
RAM Data Backup21
Execute the Backup Function21
Set the Automatic Backup for Every Suspension23
Set the Restoration Disabled after Hardware Reset23
Hardware Reset24
Cover Sensor24
Touch Panel Calibration25
Operating Panel Key27
Operating Key27
Power off28
Function Key (Soft Key)29
Star Key Mode31
Setting by Using Star Key34
Auto Power off35
Preparation for Measurement37
Power Connection37
Setting Instrument up for Measurement38
Power Switch Key on39
Battery Power Remaining Display40
Vertical and Horizontal Angle Tilt Correction41
Setting Tilt Correction by Soft Key42
Compensation of Systematic Error of Instrument43
How to Enter Numerals and Alphabet Letters44
Data Memory Card48
Active Sync49
Getting Connected49
Standard Measurement Mode50
Screen Displays50
Switching between Telescopic Image and Wide-Angle Image50
Changing the Image's Magnification51
Adjusting the Image's Contrast51
Switching the Cross-Hairs on and off52
Angle Measurement53
Measuring Horizontal Angle Right and Vertical Angle53
Switching Horizontal Angle Right/Left54
Measuring from the Required Horizontal Angle55
Vertical Angle Percent Grade(%) Mode56
Distance Measurement57
Setting of the Atmospheric Correction57
Setting of the Correction for Prism Constant57
Distance Measurement (Continuous Measurement)58
Distance Measurement (Single/N-Times Measurement)59
Fine/ Tracking / Coarse Measuring Mode60
Stake out (S.O)60
Coordinate Measurement62
Setting Coordinate Values of Occupied Point62
Setting of the Instrument Height / Reflector(Prism) Height64
Execution of Coordinate Measuring65
Data Output66
Data Output by [REC] Key67
Parameters Setting Mode68
Parameter Setting Options68
Measurement68
Communication69
Value Input69
Unit69
Setting Parameters70
Check and Adjustment71
Checking and Adjusting of Instrument Constant71
Checking the Optical Axis72
Checking the Optical Axis of EDM and Theodolite72
Checking the Optical Axis of Laser Pointer76
Checking/Adjusting the Theodolite Functions78
Checking /Adjusting the Plate Level79
Checking /Adjusting the Circular Level79
Adjustment of the Vertical Cross-Hair80
Collimation of the Instrument81
Checking/Adjusting the Cross-Hairs on Telescopic/Wide-Angle Images82
Checking / Adjusting the Optical Plummet Telescope84
Checking / Adjusting the Laser Plummet (for Laser Plummet Type)85
Adjustment of Vertical Angle 0 Datum86
How to Set the Instrument Constant Value87
Compensation Systematic Error of Instrument88
Adjustment of Compensation Systematic Error of Instrument88
Showing Compensation Systematic Error of Instrument90
Setting the Prism / Non-Prism Constant Value91
Setting Atmospheric Correction92
Calculation of Atmospheric Correction92
Setting of Atmospheric Correction Value93
Correction for Refraction and Earth Curvature98
Distance Calculation Formula98
Power Source and Charging99
On-Board Battery BT-61Q99
Detach/Attach of Tribrach101
Special Accessories102
Battery System105
Prism System106
Precautions107
Message/Error Displays108
Message108
Error108
Specifications109
Appendix112
Dual Axis Compensation112
Index114

Topcon GPT-7003i - Function Key (Soft Key)

Table of Contents

Related product manuals