Topcon IS01 - Page 164

To Previous Page

TOPCON CORPORATION

5-1 Hasunuma-cho, Itabashi-ku, Tokyo 174-8580, Japan

www.topcon.co.jp

Main Page

Foreword3
General Handling Precautions4
Display for Safe Use5
Safety Cautions5
User6
Exceptions from Responsibility6
Laser Safety7
Labels7
Symbol Mark While the Laser Is Emitting8
Table of Contents9
Contents9
Nomenclature and Functions12
Nomenclature12
Display14
Main Menu Contains14
Measurement Menu15
Display Marks15
Display Keys16
Shortcut Keys16
Backlight, Key Light Adjustment17
How to Adjust Reducing Time of Backlight17
Adjust the Backlight Brightness by Manual19
Selecting the Automatic Lighting Option20
Selecting the Key Light Option21
RAM Data Backup22
Execute the Backup Function22
Set the Automatic Backup for Every Suspension24
Set the Restoration Disabled after Hardware Reset24
Hardware Reset25
Cover Sensor25
Touch Panel Calibration26
Operating Panel Key28
Operating Key28
Turning off the Touch Panel Function29
Power off29
Operation Key(Touch Panel)30
Star Key Mode32
Switching Measurement Distance Modes36
Setting by Using Star Key37
Auto Power off38
Focus Function40
Manual Focus40
Assist Focus40
Setting Focus Function41
Rotating Method42
Rotating by H/V Shuttle and H/V Jog42
Auto Inversion42
Rotating Automatically to a Required Horizontal and Vertical Angle42
Using Together with RC-3 Remote Control System43
Using Connecting with Personal Computer (PC)44
Using the USB Port45
Preparation for Measurement46
Power Connection46
Setting Instrument up for Measurement47
Power Switch Key on48
Battery Power Remaining Display49
Vertical and Horizontal Angle Tilt Correction50
Setting Tilt Correction by Operation Key51
Correction of a Tilt Sensor Setting Error51
Compensation of Systematic Error of Instrument52
How to Enter Numerals and Alphabet Letters53
Data Memory Card57
Active Sync58
Getting Connected58
Confirming the Bluetooth® Device Address and Setting the PIN Code58
Inclination of Prism and Measuring Error59
Automatic Tracking / Automatic Collimation61
Automatic Tracking62
Automatic Collimation64
Range of Laser for Auto-Tracking and Auto-Collimating65
Setting Parameters for Auto-Tracking66
Setting Items66
How to Set the Parameters68
Standard Measurement Mode69
Screen Displays69
Switching between Telescopic Image and Wide-Angle Image69
Changing the Image's Magnification70
Adjusting the Image's Brightness70
Switching the Cross-Hairs on and off71
Angle Measurement72
Measuring Horizontal Angle Right and Vertical Angle72
Switching Horizontal Angle Right/Left73
Measuring from the Required Horizontal Angle74
Vertical Angle Percent Grade(%) Mode75
Automatic Rotation to a Required Horizontal and Vertical Absolute Angle76
Distance Measurement77
Setting of the Atmospheric Correction79
Setting of the Correction for Prism Constant79
Setting Measurement Distance Range of Non-Prism Long Mode79
Distance Measurement (Continuous Measurement)81
Distance Measurement (Single/N-Times Measurement)82
Fine / Coarse Measuring Mode83
Stake out (S.O)84
Coordinate Measurement86
Setting Coordinate Values of Occupied Point86
Setting of the Instrument Height / Reflector(Prism) Height88
Execution of Coordinate Measuring89
Data Output90
Data Output by [REC] Key91
Data Output of IS Series92
Program Mode93
Setting a Direction Angle for Backsight Orientation(BS)94
Remote Elevation Measurement (REM)96
Missing Line Measurement (MLM)99
Repetition Angle Measurement (REP)101
AP-L1A Communication Emulator103
Activate AP-L1A Communication Emulator103
Setup for Communication104
Edge Abstraction Mode105
Displayed Messages106
Parameters Setting Mode107
Parameter Setting Options108
Measurement108
Communication109
Value Input110
Unit110
Setting Parameters111
Check and Adjustment112
Checking and Adjusting of Instrument Constant112
Checking of the Accuracy of the Non-Prism Mode / Non-Prism Long Mode112
Checking the Optical Axis113
Checking the Optical Axis of EDM and Theodolite113
Checking the Optical Axis of Laser Pointer117
Inspection and Adjustment of Optic Axis for Auto -Tracking119
Checking/Adjusting the Theodolite Functions121
Checking /Adjusting the Plate Level122
Checking /Adjusting the Circular Level122
Adjustment of the Vertical Cross-Hair123
Collimation of the Instrument124
Checking/Adjusting the Cross-Hairs on Telescopic/Wide-Angle Images125
Checking / Adjusting the Optical Plummet Telescope127
Adjustment of Vertical Angle 0 Datum128
How to Set the Instrument Constant Value129
Compensation Systematic Error of Instrument130
Adjustment of Compensation Systematic Error of Instrument130
Showing Compensation Systematic Error of Instrument132
Self Checking Mode133
Setting the Prism / Non-Prism Constant Correction Value135
Setting Atmospheric Correction136
Calculation of Atmospheric Correction136
Setting of Atmospheric Correction Value137
Correction for Refraction and Earth Curvature142
Distance Calculation Formula142
Power Source and Charging143
On-Board Battery BT-65Q143
Detach/Attach of Tribrach145
Special Accessories146
Battery System148
Prism System149
Precautions150
Message/Error Displays151
Message151
Error152
Specifications154
Appendix159
Dual Axis Compensation159
Index161

Topcon IS01 - Page 164

Table of Contents

Related product manuals