TSC TDP-225 Series - User Manual

TSC TDP-225 Series

36 pages

To Next Page

To Next Page

Loading...

;’RFTGTT5RT12

TDP-225 Series

Desktop Barcode Printers

User Manual

Series Lists:

TDP-225 / TDP-225W

TDP-324 / TDP-324W

 Direct Thermal

Other manuals for TSC TDP-225 Series

Service Manual35 pages

Questions and Answers:

C
Carolyn CooperSep 10, 2025
Why is my TSC Barcode Reader not printing?
- E
  Edwin KimSep 12, 2025
  If your TSC Barcode Reader isn't printing, start by ensuring the interface cable is securely connected. If using a serial port, verify that the cable is pin-to-pin connected; if not, replace it. Also, confirm that the serial port settings match between your host and the printer, or reset the serial port setting. Check that the correct printer port is selected in the Windows driver. Finally, for Ethernet connections, ensure the IP address, subnet mask, and gateway are properly configured.
A
Allison WardSep 9, 2025
How to resolve a 'Cutter Error' on my TSC Label Maker?
- R
  Renee GarciaSep 9, 2025
  If your TSC Label Maker displays 'Cutter Error', it could be due to several reasons. First, check for a cutter jam and remove any jammed labels. If there is no cutter installed on the printer, ensure that the media thickness is equal to or less than 0.19mm. If the cutter or cutter driver circuit board is damaged, replace the affected component.
C
Craig BaldwinSep 8, 2025
What does 'Take Label' mean on my TSC Label Maker and how do I resolve it?
- K
  kurtbarnettSep 8, 2025
  If your TSC Label Maker displays 'Take Label', and the peeler function is enabled, take the label away to print the next one, especially if a peeler module is installed. If the peeler module is installed and the label has been removed but the message remains, check if the peeler module connector is properly connected to the main board. If no peeler module is installed, disable the peeler function.
R
rodriguezlauraAug 23, 2025
What to do if my TSC TDP-225 has a paper jam?
- J
  Jennifer LopezAug 23, 2025
  If your TSC Barcode Reader shows a 'Paper Jam' error, calibrate the gap/black mark sensor. Ensure the label size is set correctly in your labeling software. Also, check for and remove any labels stuck inside the printer mechanism near the sensor area.
S
sullivangregorySep 5, 2025
How to resume printing on a paused TSC Label Maker?
- K
  Kim PadillaSep 6, 2025
  If your TSC Label Maker is paused, press the FEED button to resume printing.
T
Tammie WilliamsSep 4, 2025
What does 'Head Open' mean on my TSC Label Maker?
- A
  Adam RobertsSep 4, 2025
  If the TSC Label Maker displays 'Head Open', it means the printer top cover is open. Please close the top cover.
V
valerie45Sep 3, 2025
What to do if my TSC Label Maker says 'No Paper'?
- J
  Jessica SmithSep 3, 2025
  If your TSC Label Maker displays 'No Paper', it could be due to a few reasons. You might be running out of labels, so try supplying a new label roll. Alternatively, the label roll may be installed incorrectly; refer to the user’s manual for the correct reinstallation steps. It's also possible that the gap/black mark sensor needs calibration.
T
travis26Sep 2, 2025
Why is my TSC Label Maker continuously feeding labels?
- T
  thomassnyderSep 2, 2025
  If your TSC Label Maker is continuously feeding labels, the printer settings may be incorrect. To resolve this, perform the initialization and gap/black mark calibration.
S
staceyfletcherSep 1, 2025
Why is my TSC Label Maker producing poor print quality?
- S
  Susan KingSep 1, 2025
  If your TSC Label Maker is producing poor print quality, ensure that the top cover is completely closed and that both the right and left side levers are properly latched. Check that the correct 24V DC power supply is connected to the printer. Reload the supply and verify it's loaded correctly. Finally, inspect the print head for any accumulated dust or adhesives and clean it if necessary.
L
lisawhiteAug 31, 2025
How to troubleshoot a paper jam in my TSC Label Maker?
- H
  Hannah LynchAug 31, 2025
  If the TSC Label Maker is experiencing a paper jam, there are several potential causes. First, the gap/black mark sensor sensitivity might not be set properly; try calibrating the sensor. Second, ensure that the label size is correctly set in your labeling software or program to match the installed paper. Lastly, check for any labels stuck inside the printer mechanism near the sensor area and remove them.

TSC TDP-225 Series Specifications

General

Print Method	Thermal Transfer / Direct Thermal
Resolution	203 DPI
Memory	8 MB Flash
Processor	32-bit RISC
Interface	USB 2.0
Power Supply	100-240V AC, 50/60Hz
Operating Temperature	5°C to 40°C (41°F to 104°F)
Storage Temperature	-40°F to 140°F (-20°C to 60°C)
Label Width	60 mm (2.36")

Related product manuals

Preview: TSC TDP-225

Preview: TSC TDP-245 Plus

TSC TDP-245 Plus

Preview: TSC TDP-244 Series

TSC TDP-244 Series

Preview: TSC TTP-346M

Preview: TSC TTP-268M

Preview: TSC TTP-2410M

TSC TE310 Series

Preview: TSC TTP-244 Plus

TSC TTP-244 Plus

Preview: TSC TTP-246M Pro

TSC TTP-246M Pro

Preview: TSC TC200 Series

TSC TC200 Series

Preview: TSC TE210 Series

TSC TE210 Series