TSC TDP-225 Series User Manual

TSC TDP-225 Series

36 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

;’RFTGTT5RT12

TDP-225 Series

Desktop Barcode Printers

User Manual

Series Lists:

TDP-225 / TDP-225W

TDP-324 / TDP-324W

 Direct Thermal

Other manuals for TSC TDP-225 Series

Service Manual35 pages

Questions and Answers:

M
Michael MartinezAug 29, 2025
What to do if my TSC Label Maker shows an error?
- P
  Patricia BentleyAug 30, 2025
  If your TSC Label Maker displays an 'Error' message, it could be due to a few reasons. First, check if you are out of labels or ribbon. If so, load a new roll of labels or ribbon, following the loading instructions, and then press the FEED button to resume printing. If the error persists, the printer settings might be incorrect. In this case, initialize the printer using the 'Power on Utility' or 'Diagnostic Tool'.
K
Kathryn CoxAug 28, 2025
How to fix a TSC Label Maker that shows no response?
- J
  Jennifer GuerraAug 29, 2025
  If your TSC Label Maker is showing 'No response', start by turning on the power switch. Check if the green LED is lit on the power supply; if it's not, the power supply is likely broken. Also, ensure that both power connections—from the power cord to the power supply and from the power supply to the printer power jack—are securely connected.
S
sanchezerinAug 27, 2025
Why is my TSC Label Maker not printing?
- M
  Miss Alicia Brown DVMAug 27, 2025
  If your TSC Label Maker isn't printing, several factors could be the cause. Ensure the interface cable is securely connected. If using a serial port, the cable's pin configuration must be pin-to-pin; if it is not, replace the cable. Also, verify that the serial port settings are consistent between your host and the printer, and that the correct printer port is selected in the Windows driver. For Ethernet connections, confirm that the IP address, subnet mask, and gateway are properly configured.
W
Wyatt KempAug 27, 2025
How do I fix a paper jam on my TSC TDP-225 Barcode Reader?
- B
  bennettarthurAug 27, 2025
  If your TSC Barcode Reader displays 'Paper Jam', calibrate the gap/black mark sensor. Ensure the label size is set correctly. Remove any jammed labels from inside the printer mechanism.
M
Melissa RyanAug 25, 2025
How to fix 'Out of Mem' error on my TSC Barcode Reader?
- P
  Paul StricklandAug 26, 2025
  If your TSC Barcode Reader displays 'Out of Mem', delete unused files from the FLASH/DRAM or MicroSD card to free up space.
S
Steven WrightAug 25, 2025
How to improve print quality on my TSC TDP-225?
- J
  Jennifer ReynoldsAug 25, 2025
  If your TSC Barcode Reader is producing poor print quality, ensure the top cover is completely closed and latched on both sides. Verify that the correct 24V DC power supply is connected. Reload the supply correctly. Clean the print head if dust or adhesives have accumulated. Adjust the print density and speed settings. Run a self-test to check the print head test pattern for any missing dots.

TSC TDP-225 Series Specifications

General

Print Method	Thermal Transfer / Direct Thermal
Resolution	203 DPI
Memory	8 MB Flash
Processor	32-bit RISC
Interface	USB 2.0
Power Supply	100-240V AC, 50/60Hz
Operating Temperature	5°C to 40°C (41°F to 104°F)
Storage Temperature	-40°F to 140°F (-20°C to 60°C)
Label Width	60 mm (2.36")

Related product manuals

Preview: TSC TDP-225

Preview: TSC TDP-245 Plus

TSC TDP-245 Plus

Preview: TSC TDP-244 Series

TSC TDP-244 Series

Preview: TSC TTP-346M

Preview: TSC TTP-268M

Preview: TSC TTP-2410M

TSC TE310 Series

Preview: TSC TTP-244 Plus

TSC TTP-244 Plus

Preview: TSC TTP-246M Pro

TSC TTP-246M Pro

Preview: TSC TC200 Series

TSC TC200 Series

Preview: TSC TE210 Series

TSC TE210 Series