How to fix a paper jam in my TSC TTP-225 Barcode Reader?
To address a paper jam in your TSC Barcode Reader, calibrate the gap/black mark sensor. Ensure the label size is correctly set in your labeling software. Also, check for and remove any labels stuck inside the printer mechanism near the sensor area.
What to do if my TSC Printer is not printing?
If your TSC printer isn't printing, several factors could be at play. First, ensure the interface cable is securely connected. If using a serial port, verify the cable is pin-to-pin connected; if not, replace it. Also, confirm that the serial port settings match between your host device and the printer. In the Windows driver, select the correct printer port. If you're using Ethernet, check that the IP address, subnet mask, and gateway are configured correctly. Re-connecting the cable to the interface may also resolve the issue.
Why is my TSC Barcode Reader's print quality poor?
To resolve poor print quality on your TSC Barcode Reader, ensure the top cover is completely closed and latched properly. Verify that the correct 24V DC power supply is connected. Reload the supply correctly. Clean the print head if there's dust or adhesive accumulation. Adjust the print density and print speed. Finally, run a printer self-test to check the print head test pattern for any missing dots.
How to troubleshoot a TSC Barcode Reader with no response?
If your TSC Barcode Reader is not responding, first, ensure the power switch is turned on. Check if the green LED on the power supply is lit; if not, the power supply might be broken. Also, verify that both power connections, from the power cord to the power supply and from the power supply to the printer, are securely connected.
What to do if my TSC Printer has a cutter error?
If your TSC printer is displaying a cutter error, first, remove any jammed labels. Next, ensure that the media thickness is equal to or less than 0.19mm. If the problem persists, the cutter or cutter driver circuit board may be damaged, and you should replace the cutter or cutter driver circuit board.
What causes 'Head Open' error on TSC Printer and how to fix it?
The 'Head Open' error on your TSC printer indicates that the top cover is open. Close the top cover to resolve the issue.
How to stop continuous feeding of labels on my TSC Printer?
If your TSC printer is continuously feeding labels, the printer setting may be incorrect. Please perform the initialization and gap/black mark calibration to resolve this issue.
What to do if TSC Printer is paused?
If your TSC printer is paused, simply press the FEED button to resume printing.
How to resolve 'No Paper' error on TSC Printer?
If your TSC printer displays a 'No Paper' error, first, supply a new label roll if the current one is depleted. If the error persists, ensure the label roll is installed correctly by referring to the user’s manual for the proper steps. Lastly, calibrate the gap/black mark sensor, as it may not be properly calibrated.
What to do if my TSC Printer has a paper jam?
If your TSC printer is experiencing a paper jam, consider these steps: First, calibrate the gap/black mark sensor, as the sensitivity might not be set correctly. Next, ensure the label size is accurately set in your labeling software or program to match the installed paper. Finally, check for and remove any labels stuck inside the printer mechanism near the sensor area.
Overview of the TSC bar code printer's features and performance capabilities.
Lists the safety and regulatory compliances for the printer, including CE, FCC, UL, CUL, C-Tick, and TÜV.
Crucial safety information regarding hazardous parts, battery risks, and proper disposal.
Guide on how to unpack the printer and verify all included items are present.
Visual identification of the printer's main external components.
Identifies components on the front of the printer, such as LCD display and buttons.
Identifies internal components of the printer, like print head, sensors, and rollers.
Identifies rear ports and interfaces, including power, USB, and serial connections.
Step-by-step instructions for initially setting up the printer on a surface.
General instructions for loading different types of media into the printer.
Detailed procedure for loading standard media rolls into the printer.
Instructions for loading media specifically for the peel-off label dispensing function.
Instructions for loading media when using the printer's cutter function.
Procedure for loading thicker media, requiring adjustments to the printer's internal guides.
Step-by-step guide on how to properly install the thermal transfer ribbon.
Introduction to the diagnostic utility for printer configuration and troubleshooting.
Details on printer functions like sensor calibration, Ethernet, and RTC setup via the diagnostic tool.
Guide on configuring Ethernet settings using the diagnostic utility.
Steps to configure the printer's Ethernet using a USB connection.
Steps to configure the printer's Ethernet using an Ethernet connection.
Instructions for installing a MicroSD card into the printer.
Guide on using a USB keyboard with the printer for stand-alone operations.
Explanation of the LED colors and their meanings indicating printer status.
Description of the primary functions of the printer's feed button.
Overview of special functions activated by powering on the printer with the button held.
Procedure for calibrating the gap or black mark sensor for media detection.
Steps for calibrating sensors, performing a self-test, and entering dump mode.
Process to reset printer settings and clear memory to factory defaults.
Instructions to set the black mark sensor for media detection and calibrate it.
Instructions to set the gap sensor for media detection and calibrate it.
Method to bypass the automatic execution of the AUTO.BAS program on startup.
Common printer issues identified by LED status and their recovery procedures.
Lists various printing issues and their possible causes and solutions.
Explains LCD messages and provides solutions for encountered printer errors.
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Resolution | 203 DPI (8 dots/mm) |
| Model | TTP-225 Series |
| Memory | 8 MB Flash, 4 MB SDRAM |
| Interface | USB 2.0 |
| Processor | 32-bit RISC |
| Type | Barcode Printer |
| Supported Barcodes | Code 39, Code 128, UPC-A, UPC-E, EAN-8, EAN-13, Interleaved 2 of 5, Codabar, POSTNET |
| Operating Temperature | 5 ~ 40°C (41 ~ 104°F) |
| Humidity | 85% RH (non-condensing) |
| Media Type | Continuous, Die-Cut Labels |
| Storage Temperature | -40 ~ 60°C (-40 ~ 140°F) |
To Next Page
