To Next Page
C
cody05Sep 16, 2025
Why is the RTC time incorrect when I reboot my TSC Printer?
- CchristinejohnsonSep 16, 2025
If the RTC time is incorrect when you reboot your TSC Printer, check if there is a battery on the main board.
Why is the RTC time incorrect when I reboot my TSC Printer?
If the RTC time is incorrect when you reboot your TSC Printer, check if there is a battery on the main board.
Why is my TSC Printer not printing anything on the label?
If your TSC Printer is not printing on the label, consider the following: * Ensure the label and ribbon are loaded correctly, following the loading instructions. * Verify that the ribbon and media are compatible. * Reload the ribbon, ensuring the inked side is correct. * Clean the printhead. * Check that the print density setting is correct.
How to fix poor print quality on my TSC Printer?
To resolve poor print quality on your TSC Printer: * Reload the ribbon and media. * Clean the print head and platen roller. * Adjust the print density and print speed. * Run a printer self-test to check the print head test pattern for missing dots. * Change to a proper ribbon or label media. * Adjust the printhead pressure adjustment knob.
What to do if my TSC Printer says 'No Paper'?
If your TSC Printer indicates 'No Paper', consider these solutions: * Supply a new label roll. * Reinstall the label roll, referring to the user manual for guidance. * Calibrate the gap/black mark sensor.
Why does my TSC Printer skip labels when printing?
If your TSC Printer is skipping labels, try these solutions: * Check if the label size is set up correctly. * Calibrate the sensor using Auto Gap or Manual Gap options. * Clear any dust from the GAP/Black mark sensor using a blower.
How do I resolve wrinkle problems when printing with my TSC Printer?
To address wrinkle problems with your TSC Printer: * Refer to section 4.2. * Set a suitable print density for good print quality. * Ensure the label guide touches the edge of the media guide.
What does 'Carriage Open' mean on my TSC Printer?
If your TSC Printer displays 'Carriage Open', please close the print carriages.
Why is the peel sensor not working on my TSC Printer?
If the peel sensor is not working on your TSC Printer: * Ensure that the media goes through the Peel sensor. * Plug the connect cable correctly.
Why is the left side printout position incorrect on my TSC Printer?
If the left side printout position is incorrect on your TSC Printer: * Set the correct label size. * Fine-tune the Shift X parameter by pressing [MENU] [SELECT] x 3 [DOWN] x 5 [SELECT].
Why is my TSC Printer printing a gray line on blank labels?
If your TSC Printer is printing a gray line on blank labels, clean the print head and the platen roller.
General| Print Speed | 4 ips / 6 ips |
|---|---|
| Memory | 512 MB Flash, 512 MB SDRAM |
| Interface | USB 2.0, Serial, Ethernet |
| Type | Industrial Printer |
| Print Method | Thermal Transfer / Direct Thermal |
| Print Resolution | 203 dpi |
| Communication Interface | USB 2.0, Serial, Ethernet |
| Label Thickness | 0.003" (0.076 mm) ~ 0.012" (0.305 mm) |
| Power Supply | 100 - 240 VAC, 50/60 Hz |
| Operating Temperature | 5 ~ 40°C (41 ~ 104°F) |
| Storage Temperature | -40 ~ 60°C (-40 ~ 140°F) |
| Resolution | 203 dpi |
| Operating Humidity | 20 - 85% RH (non-condensing) |
Details the physical and functional specifications of the printer models, including features and capabilities.
Covers overall physical dimensions, weight, power requirements, and environmental operating conditions.
Details print head resolution, printing method, dot size, print speed, maximum width, and length.
Lists specifications related to the printer's ribbon, including diameter, length, width, and wound type.
Outlines media capacity, alignment, types, wound type, width, thickness, and core diameter requirements.
Explains the process of unpacking the printer and verifying all included components.
Provides visual identification and descriptions of the printer's front, interior, and rear components.
Describes the printer's control panel, including LED indicators, touch screen functions, and operational keys.
Provides step-by-step instructions for initial printer setup, including connections and power.
Details the procedure for correctly installing and threading the printer ribbon.
Explains the process of loading various types of media, including sensor calibration.
Guides on loading fan-fold or external media, often used with optional accessories.
Details the procedure for loading media specifically for operation with the cutter module.
Describes the process of loading media for use in the peel-off mode.
Explains how to adjust printer parts and knobs to prevent ribbon wrinkles during printing.
Guides on launching the TSC Console software and initiating printer management.
Provides instructions for configuring the printer's Ethernet network connection and IP settings.
Steps to configure Wi-Fi security and network settings and add the printer to the console.
Procedures to reset the printer's Wi-Fi module to its factory default configuration.
Overview of various printer functions accessible through the console, like calibration and test pages.
How to configure printer actions that occur after a print job, such as cutting or peeling.
Instructions on how to access the printer's main menu using the LCD panel and keys.
Provides a summary of the 8 main categories available in the printer's LCD menu system.
Explains how to configure printer settings using the TSPL command language.
Details how to configure printer settings using the ZPL2 command language.
Describes the process and options for calibrating the printer's media and gap sensors.
Covers settings for managing the printer's communication interfaces like Serial, Ethernet, Wi-Fi, and Bluetooth.
Information on accessing and managing files stored in the printer's memory.
Features for checking printer status, running tests, and diagnosing operational issues.
Access to advanced settings for display, touchscreen, date/time, cutter type, and language.
Options for restoring printer settings to defaults, checking information, and contacting support.
Addresses issues where the printer's power indicator is not visible.
Troubleshooting steps for when the printer's carriage is open or not properly closed.
Covers common causes and solutions for the printer failing to print.
Addresses issues where labels are not receiving any printed output.
Troubleshooting steps related to ribbon installation, loading, or running out.
Solutions for problems related to the printer not detecting or feeding paper.
Step-by-step guidance to resolve paper jams within the printer mechanism.
Troubleshoots issues with labels not being dispensed or taken correctly.
Solutions for errors encountered when transferring files to the printer's memory.
Addresses common causes and solutions for print output that is unclear or of low quality.
Solutions for print missing on the sides of the label.
Troubleshoots the appearance of unwanted gray lines on blank labels.
Solutions for print patterns that are inconsistent or uneven.
Addresses issues with unstable or skewed label feeding during the printing process.
Troubleshooting steps when the printer skips labels during operation.
Solutions for ribbon or media wrinkles that occur during printing.
Fixes for incorrect real-time clock settings after the printer restarts.
Correcting the print position on the left side of the label.
Adjusting the print position specifically for small labels.
Troubleshooting steps for a dark LCD panel and unresponsive control keys.
Addresses issues where the LCD is dark but the status LEDs are illuminated.
Solutions for a non-functional or improperly detected ribbon encoder sensor.
Troubleshooting steps for a faulty or unresponsive ribbon end sensor.
Solutions for when the printer's integrated cutter mechanism fails to operate.
Details the methods and intervals for cleaning printer parts like the print head, platen roller, and sensors.
