Name: TurboChef i5
Brand: TurboChef
Rating: 5 (1 reviews)

To Next Page

To Previous Page

A-12 APPENDIX - REPLACING OVEN COMPONENTS

Figure

Reference #

Item Description Item Part Number Hardware Description Hardware Part Number(s)

1 Hinge, Bracket, Slide, LHS I5-9196 Nut, Keps, Hex, #8-32, Ext Tooth, Cres 102962 (qty 4)

2 Hinge, Bracket, Slide, RHS I5-9195 Nut, Keps, Hex, #8-32, Ext Tooth, Cres 102962 (qty 4)

3 Hinge, Cam, Weldment, LHS I5-9313 Washer, Nylon, Hingepin C0504 (qty 1)

4 Hinge, Cam, Weldment, RHS I5-9314 Washer, Nylon, Hingepin C0504 (qty 1)

5 Hinge, Guide, Switch Slide, Lower I5-9316 Screw, 10-32 x 3/8 lg, PFLH, 100 Deg, SS 101401 (qty 2)

6 Hinge, Guide, Switch Slide, Upper I5-9315 Nut, Keps, Hex, #8-32, Ext Tooth, Cres 102962 (qty 4)

7 Hinge, Gusset, LHS I5-9178 Nut, 1/4 - 20, Serr, Hex Flange, Plated Steel 100906 (qty 2)

8 Hinge, Gusset, RHS I5-9179 Nut, 1/4 - 20, Serr, Hex Flange, Plated Steel 100906 (qty 2)

9 Hinge Module, Base I5-9193 None None

10 Hinge, Torsion Bar I5-9144 Spacer, Adjustment Call TurboChef

11 Hinge, Weldmt, Ctrblnce Brkt, LHS I5-9326 Screw, 10-32 x 3/8 lg, PFLH, 100 Deg, SS 101401 (qty 3)

12 Hinge, Weldmt, Ctrblnce Brkt, RHS I5-9327 Screw, 10-32 x 3/8 lg, PFLH, 100 Deg, SS 101401 (qty 3)

13 Magnetron (Left) NGC-3015 Screw, Sh Mtl #8 x 1/2, Serrated PHTRH 101688 (qty 4)

14 Magnetron (Right) NGC-3015 Screw, Sh Mtl #8 x 1/2, Serrated PHTRH 101688 (qty 4)

15 Thermostat, Magnetron (Left) 102070 Screw, Sh Mtl, Drill Point, 6-32 x 3/8, PPHD, Zinc 101684 (qty 2)

16 Thermostat, Magnetron (Right) 102070 Screw, Sh Mtl, Drill Point, 6-32 x 3/8, PPHD, Zinc 101684 (qty 2)

17 Waveguide (Left) I5-9330 Nut, Keps, Hex, #10-32, Ext Tooth, Cres 102963 (qty 9)

18 Waveguide (Right) I5-9330 Nut, Keps, Hex, #10-32, Ext Tooth, Cres 102963 (qty 9)

19 Waveguide Gasket (Left) I5-9331 None None

20 Waveguide Gasket (Right) I5-9331 None None

Replacing Items - Removing/Opening Multiple Covers Required (Figures A-10, A-11)

DANGER: Before replacing any oven component, ensure the oven is removed from any power

source. Replacing a component while the oven is plugged in can result in serious injury or death.

CAUTION: Before removing/installing any component, make sure it is disconnected from the

wire harness (where applicable).

NOTE: Hardware listed is required for installing component to oven.

To remove the left side cover, see page A-9.

To remove the right side cover, see page A-11.

To open the top cover, see page A-5.

TurboChef i5 Service Manual

Other manuals for TurboChef i5