What does ‘Low Heat’ mean on my Tuttnauer 3850E?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 3850E?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 3850E process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer 3850E machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer 3850E Laboratory Equipment shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer 3850E Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer 3850E?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer 3850E displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 3850E Laboratory Equipment is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer 3850E leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Inspect the autoclave for damage upon arrival and document any findings.
Details warranty coverage, activation process, and repair procedures.
Provides electrical specifications and fuse/breaker ratings.
Details overall dimensions and physical specifications.
Details the purpose and operation of each key on the control panel.
Explains various messages and associated safety measures displayed by the unit.
Covers programs for unwrapped, wrapped items, glassware, and dry only.
Guides for first-time use, program selection, and starting a cycle.
Outlines daily, weekly, and periodic maintenance procedures.
Solutions for low heat, low water, low pressure, low temperature, and unresponsiveness.
General| Brand | Tuttnauer |
|---|---|
| Model | 3850E |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
