TYM ET350 ECONO - User Manual

Questions and Answers

C
christopherwalkerAug 9, 2025
What to do if my TYM ET350 ECONO lacks lifting force?
- D
  delacruzbenjaminAug 9, 2025
  If your TYM Tractor lacks lifting force or the lifter won't lift, there are several potential causes. It could be due to a low oil level or the use of an improper oil type, in which case you should add the proper oil to the specified level. Another cause may be a clogged oil inflow strainer, which requires flushing the strainer. Other possible issues include air in the hydraulic system (drain and tighten the contactor or replace the seal ring), a seriously worn oil pump (replace the oil pump seal ring), an open lower valve (dismount and clean), seriously worn main control or return valves (replace worn parts), an ineffective safety valve (readjust or repair), a cylinder leak (replace the seal ring or worn parts), or leakage at the distributor seal rings (replace the seal rings).
C
Chelsea VelazquezAug 15, 2025
Why does the clutch slip on my TYM ET350 ECONO?
- Z
  zbellAug 15, 2025
  The clutch on your TYM Tractor might be slipping due to several reasons. The friction disk could be stained with oil, requiring you to flush it with gasoline and remove the oil leakage. Alternatively, the pressing spring might be weakened or broken, necessitating its replacement. Another potential cause is short or no pedal free travel, which can be resolved by readjusting the pedal free travel according to the specification. It is also possible that the driven disk is curved, unevenly worn, or excessively worn out, in which case you should rectify or replace it. Finally, the tree-release-lever end forces might not be in the same plane, requiring adjustment of the release lever end faces.
G
grobertsAug 25, 2025
What to do if the brakes on my TYM ET350 ECONO disengage incompletely?
- J
  Jill CastroAug 26, 2025
  If the brakes on your TYM Tractor disengage incompletely and overheat, several factors could be responsible. The return spring may be weakened, requiring replacement. The brake pedals might not be returning; inspect the return spring for damage and the shaft for being gripped, and remove any obstructions. Also, short pedal free travel can cause this issue, so readjust the pedal free travel.
S
Sharon ColeAug 29, 2025
Why won't the generator work on my TYM ET350 ECONO?
- J
  Joseph ChristensenAug 30, 2025
  If the generator on your TYM Tractor isn't working, it could be due to a damaged rectifying unit, which would require repairing or replacing the rotator winding or stator winding. Another potential cause is a block brush that is gripped and not making contact with the collector ring; repair or replace the block blush spring in this case. Additionally, the stator winding or rotator winding could have a broken circuit, short circuit, or defective insulation between the negative pole and terminals. Adjust the belt tension or replace the belt.
S
Sean RamseySep 4, 2025
How to fix abnormal sound in the transmission box of TYM ET350 ECONO?
- B
  Bryan KennedySep 4, 2025
  An abnormal sound in the transmission box of your TYM Tractor may be due to several issues. The transmission box bearing or rolling needle could be excessively worn or damaged, requiring you to check and replace the worn parts. It could also be caused by abnormal meshing of the main drive gears; examine the meshing traces and backlash, and adjust them according to regulations. Lastly, worn shaft splines and gear splined holes can cause this issue, so replace the worn parts.
D
David MillerSep 10, 2025
What to do if my TYM ET350 ECONO has frequently insufficient electric power?
- J
  Joanne WalshSep 12, 2025
  If your TYM Tractor is experiencing frequently insufficient electric power, consider the following: * Check the electrolyte level and add to the specified level if it's low. * If there are short-circuited plates, clean the deposit, change the electrolyte, and replace spacers or plates. * If the plates are sulphurized, charge repeatedly to remove the sulphur. * Inspect for a defective generator or regulator, and repair as needed. * Examine the wire contraction to eliminate any issues.