2.2.2 NOISE AND VIBRATIONS LEVELS
7$
Declared
acoustic pressure emission level l at the operator's worksiten
$l
;ouA<
;AuA<
Declared
o
acoustic output level l
n
Hl9
;tuA<
;touA<
Declared
p
cumulative value of the acceleration of vibrations transmitted to the
operator’s hand-arm
B9
;A:pu?:A< :
?
;p:>u?:< :
?
+(>@!)/(n
2.2.3 SAFETY PICTOGRAMS
The user is obliged to keep the pictograms on the machine in a legible state and, in case of any damage, ensure their replacement.
! ) (! 7$!
Combined sticker (
D:??
), which is
attached under the rear plastic cover on the
machine's frame
> Before using the machine, read through these Operating Instructions.
?
When doing maintenance on the machine, disconnect the spark plug
connector.
@
It is forbidden to place your hands or feet into the operating area of the
cutting tool – risk of getting cut.
A
Risk of being hit by flying debris, cuttings, ejected items, etc. Other persons
and animals - keep a safe distance from the machine.
During work observe the maximum permissible slope for operation.
o Use eye and hearing protection.
Separate sticker on the working tool cover.
(
D:?
)
Working tool rotation direction arrow – right (clockwise)
Sticker (
D:?@
) on the control lever on the
right handlebar.
Starting the working tool drive:
= working tool not moving
> = safety engaged
? = working tool moving
Sticker (
D:?A
) on the control lever on the
left handlebar.
Machine travel start:
= the machine is stationary
> = The machine is moving
Sticker (
D:?>
) located on the working tool
cover side, right in the travel direction.
Prohibited space for other persons and animals. Minimum safe distance from
the machine.
+(>A!%,D
2.3 BASIC INFORMATION
2.3.1 USE OF THE MACHINE
The series brush cutters are designed to eliminate tall stalk grasses during their dormancy up to the maximum
height of 80 cm in both maintained
and non-maintained areas, and woody plants
t
in forests and on meadows with the maximum
diameter of 1 cm. The areas must not feature any solid items in the growth or rougher terrain. The series brush cutters are not
designed for park growth trimming.
The series brush cutters are designed as multi-purpose machines, the cutting blade with a cover may be
replaced with other adapters, for example, for mowing long grass for hay or surface cleaning. The recommended use of the brush cutters
with other adapters is described in the operating instructions of a given adapter. Attention, the series brush cutters are
single-purpose machines, and do not support any adapter change!
+B%$$BBB$$ƒB%9(%$%
$$r
The machine may operate in all the inclined positions defined by the engine manufacturer, providing the operator is able to safely guide
the machine.
The protective devices comply with the requirementsof #)8)>?p@@ a 8)>?p@@. These standards primarily &%B
$„%, since he cannot be hit by any stones or other objects thrown by the machine's rotating mechanism during the machine’s
regular travel. Therefore, the operator must always be in his regular control position, i.e. behind the machine, and with both hands firmly
holding the handlebars.
"%( ,$% B B
55
Measured per ČSN EN ISO 11201 under the conditions specified in ČSN EN 12733+A1, Annex B
56
Per #)"K@pAA
57
Measured per ČSN EN ISO 20643 under the conditions specified in ČSN EN 12733+A1, Annex C
58
The maximum height of freshly grown grass is limited to 40 cm. The area growth must be cut at least once a year!
59
The brush cutter is not designed to cut any continuous woody growth thicker than 5 mm! l,%(B… F DB Br
?A
Revize 10/2019
To Next Page
Loading...
Need help?
General
