Vari Hurricane MaX F-580 User Manual


5) Refit the two covers. Place top plastic  > sideways under the engine plate, lock it, and tighten plastic  @. Deflect
bottom plastic  ? upwards and place the cover opening in % A on the frame projection. Release the cover deflection,
and the cover snaps into place. Do not forget to secure the bottom cover by inserting spring $ :
 &
pp
B(B D9% ,DB:
2.4.3 WORKING WITH THE MACHINE
2.4.3.1 MACHINE WORKING WIDTH
 It is always necessary to adjust the working width of the machine to the vegetation density!
We do not recommend using the maximum working width ( +(>A ) given by the working space cover design. The operator cannot
lead the machine in the terrain sufficiently straight and accurately to cut the vegetation across the full width. We recommend guiding the
machine partially (app. 5-10 cm from the working space cover edge) in the cut growth (marked by the arrow in D:>> from the operator's
view).
 By observing this instruction you will prevent un-mown strips on the maintained surface.
2.4.3.1.1 STUBBLE HEIGHT CHANGE
 lF,KBDF%BF& $,$(%$% D,F&B
,%B BrlF,FBBDK(%D, Br
The spur is factory-set to the highest possible stubble height for the most demanding terrain. If you work with any thinner, lower or
perfectly dried growth, you may reduce the stubble height down to 4 cm. You will achieve greater growth crushing. The height change is
simply made after removing $$ > by moving any number of FB ?see D:>@ .
 By moving the washers, you may select up to 21 different stubble height positions.
2.4.3.2 GROWTH CUTTING METHOD
 The growth must be free of solid items (such as stones, wires, loose debris, etc.). These items could be thrown out or could
damage the machine."%B,( 9B$:
 +B BBD$D$,:BB(% , DB:
FBFBF&D(BB B:
 HB FD$9(DB$:K,,$$9B
B9F,DBDB$:Observe the safe slope accessibility, see +(>A !
Set the maximum engine speed, let the working tool spin at its maximum speed, and then drive against the growth that you wish to get
rid of. The growth is crushed by the working tool in the cover space, and the crushed growth is directed through a specially shaped cover to
the space between the wheels, as it leaves behind the machine.
If the cut growth is very dense, prickly, rotten or beaten, it is necessary to reduce the machine’s working width proportionally in such a
way that there is no significant reduction in working tool speed and thus reduced mowing quality.
 We recommend that you proceed with your machine through the growth, so that you have uncut growth B
BGDBB D:>> . The growth is thus better processed by the blade. The reverse procedure, where
there is uncut grass on the left, is not an issue.
 Dense and tall growth lifts the machine, do not strive to keep the front spur always on the ground, but you may help the
machine by lifting it and mowing only the top of the growth with the travel off. Return to this place and finish it with the
spur already on the ground.
2.4.3.2.1 MOWING TROUBLES
 Pay special caution when lifting and backing the machine!
 lF,,B B(&F(,$BDB(FF:Always pay extra caution when moving
in the area under the raised machine! Secure it against spontaneous movement!
 HBDBF&D$9BD F,(FB%%r
 +& ~  FB D B $BB $ : D D  B$: HB
D9$,BFBF&D( 9B(B:
 lF,F%BF&D$(%$DFB,,B B:
>< +BD$9(„B&:
77 Only for .
?t
Revize 10/2019

Vari Hurricane MaX F-580 Specifications

General

Brand	Vari
Model	Hurricane MaX F-580
Category	Brush Cutter
Language	English