Vector Welding ARC 200G - Page 24

Inhalt
Hinweisezur Verwendungdieser Bedienungsanleitung
1.1 Gefahren des Lichtbogenschweißens-----------------------------------------04-08
1.2 Effekte von Niederfrequenzelektrik und magnetischen Feldern---------- 08-08
1.3 Tabelle der verwendeten Symbole---------------------------------------------- 09-09
1. Sicherheitshinweise
3. Inbetriebnahme
3.2 Bedienfeld------------------------------------------------------------------------------ 20-21
3.3 Konfiguration LIFT WIG (GTAW) Schweißen------------------------------------ 21-22
3.4 Konfiguration des STICK (MMA) Schweißen------------------------------------- 23-24
3.5 Konfiguration fürs Schneiden(CT 520PD)----------------------------------------- 24-26
3.6 Arbeitsumfeld-------------------------------------------------------------------------- 27-27
3.7 Arbeitshinweise----------------------------------------------------------------------- 27-27
3.1 Layout für die Steuertafel--------------------------------------------------------- 14-19
4. Schweißverfahren
4.1 WIG Grundlegende Schweißverfahren------------------------------------------- 28-28
4.2 Nahtformen beim WIG Schweißen------------------------------------------------- 28-28
4.3 Erklärung von Schweißqualität----------------------------------------------------- 28-28
4.4 Anpassung der Parameter beim WIG Schweißen------------------------------- 29-31
4.5 MMA Grundlegende Schweißtechniken------------------------------------------ 31-32
5. Fehlerbehebung
5.1 Grundlegende Fehlerbehebung--------------------------------------------------- 33-35
6. Instandhaltung
6.1 Instandhaltung---------------------------------------------------------------------- 35-36
2. Zusammenfassung
2.4 Spezifikationen------------------------------------------------------------------- 11-12
2.1 Kurze Zusammenfassung--------------------------------------------------------- 10-10
2.2 Funktionsprinzip---------------------------------------------------------------------- 10-10
2.3 ------------------------------------------------------- 11-11Volt- Ampere Charakteristik
2.5 Arbeitszyklus------------------------------------------------------------------------- 12-13
2.6 ------------------------------------------------------------13-13Mitgelieferte Einzelteile
Deutscher Teil 01-36
Markenbeschreibung----------------------------------------------------------------02-02
Zertifikat------------------------------------------------------------------------------------71-71
Lesen Sie das Vorwort---------------------------------------------------------------03-04
Wartungsprotokoll--------------------------------------------------------------------72-72
1.1 Arc welding damage--------------------------------------------------------------40-43
1.2 Effects of low frequency electric and magnetic fields----------------------- 43-43
1.3 Symbol chart------------------------------------------------------------------------ 44-44
1. Safety instructions
3.Operation
3.2 Control Panel------------------ -------------------------------------------------------- 54-55
3.3 Set-up for LIFT TIG (GTAW) welding---------------------------------------------- 55-57
3.4 Setup for STICK (MMA) welding---------------------------------------------------- 57-58
3.5 Setup for cutting (CT 520PD)------------------------------------------------------- 59-61
3.6 Operation Environment----------------- --------------------------------------------- 61-62
3.7 Operation Notices----------------- --------------------------------------------------- 62-62
3.1 Layout for the panel----------------------------------------------------------------- 49-54
5.Troubleshooting
4.Welding technique
5.1 Troubleshooting--------------------------------------------------------------------- 67-69
4.1 TIG Basic Welding Technique------------------------------------------------------ 62-62
4.2 Joint froms in TIG------------------------------------------------------------------- 63-63
4.3 The explanation of welding quality----------------------------------------------- 63-63
4.4 TIG Parameters Matching---------------------------------------------------------- 63-65
4.5 MMA Basic Welding Technique--------------------------------------------------- 65-66
6.Maintenance
6.1 Maintenance------------------------------------------------------------------------- 69-70
2.Summary
2.4 Specifications------------------------------------------------------------------------ 46-47
2.1 Brief Introduction--------------------------------------------------------------------45-45
2.2 Working principle--------------------------------------------------------------------45-45
2.3 Volt- Ampere Characteristic-------------------------------------------------------46-46
2.6 Packaged Items---------------------------------------------------------------------- 48-48
2.5 Duty cycle-----------------------------------------------------------------------------47-48
English version 37-70
Brand description---------------------------------------------------------------------38-38
Certificate---------------------------------------------------------------------------------71-71
Read the preface------------------------------------------------------------------------39-40
Maintenance records----------------------------------------------------------------72-72