What to do if Vibra AJ-E Scales displays [?????] before capacity?
If the Vibra Scales display shows '?????' before reaching capacity, it could be due to the gross weight exceeding the scale's capacity. Make sure to check the total weight, considering both the container and the sample. Alternatively, there might be damage to the mechanism.
Why does my Vibra AJ-E Scales weight indication contain an error?
If your Vibra Scales displays an error in weight indication, it could be due to a mistake during the tare subtraction procedure. Review the tare subtraction process. Also, ensure the adjusters are not lifted, as this can cause an incorrect level. Check the level. If the indication values are inconsistent after prolonged use or relocation, execute span adjustment on the balance.
Why is the display unstable on my Vibra Scales?
If the display of your Vibra Scales is unstable and [M] keeps flashing, this could be because the balance is exposed to air currents or vibration, or is placed on an unstable surface. Check the precautions on use. It might also happen if an object is touching the sample, the measuring pan, or the tare. Check the precautions on use.
What does [?????] displayed on Vibra AJ-E mean?
If your Vibra Scales displays '?????', it could be due to a foreign object caught between the measuring pan (or pan base) and the balance. Remove the measurement pan and examine the surface beneath it. It might also indicate damage to a section of the mechanism. Remove the measurement pan and examine the surface beneath it.
Why does limit function not work on Vibra AJ-E Scales?
If the Vibra Scales limit function is not working, it could be because the function is not selected. Check the operation of the limit function. Alternatively, the limit value might have been entered incorrectly. Check the operation of the limit function.
How to fix no display on Vibra Scales?
If your Vibra Scales shows no indication on the display, make sure that the AC adapter is properly connected.
What does [?????] displayed during span adjustment (AJ-E) on Vibra Scales mean?
During span adjustment (AJ-E) if '?????' is displayed on your Vibra Scales, it might be because a weight heavier than the capacity was used. Check that the span adjustment procedure was performed correctly. It could also mean that the reference weight is less than 50% of the capacity. Check that the span adjustment procedure was performed correctly. Another possibility is that the calibration produced an error of 1.0% or more. Check that the span adjustment procedure was performed correctly.
What to do if [???] appears on Vibra AJ-E Scales?
If '[???]' appears on your Vibra Scales (with '[?]' and a value flashing at '[LO]'), it's likely due to insufficient sample weight in the counting mode. To resolve this, execute the Memory Update Method.
What does [?????] displayed at span adjustment (AJH-E) on Vibra AJ-E Scales mean?
If at span adjustment (AJH-E) '?????' is displayed on your Vibra Scales, it may be because the adjustment was performed with something loaded on the measurement pan. Check the correct span-adjustment procedure.
Why does Vibra AJ-E indication disappear during battery installation?
If during battery installation the indication disappears, '[ ]' flashes, or no indication is produced on your Vibra Scales, it could be because the automatic power-off function was activated. Switch the power on again and deactivate the automatic power-off function if necessary. Alternatively, the battery capacity might be low; recharge the battery.
Details the balance's display indicators and their functions.
Describes the purpose and operation of each key on the balance.
Step-by-step guide for setting up the balance correctly.
Guide on configuring and verifying balance functions.
Steps to configure the limit function for measurement discrimination.
Setting limit values by weighing actual samples.
Entering limit values numerically using the balance keys.
Procedure for calibrating the AJ-E series balances.
Procedure for calibrating the AJH-E series balances.
General| Stabilization Time | 2 sec |
|---|---|
| Interface | RS232C |
| Units | g, lb, oz |
| Calibration | External Calibration |
| Material | Stainless Steel (Pan) |
| Platform Size | Ø128mm, 170(W) x 140(D)mm |
To Next Page
