Videx 4000 Series - Page 39

66250754-EN - V1.0 - 18/02/19
- 39 -
4000 Series GSM Audio Intercom - Technical Manual
4000 Series GSM Audio Intercom with Proximity
Programming the GSM Intercom
Store an access code with an
access level (including storing in
known and next free location &
also relay setup)
PIN 1111PINnnn”code”An
or
1111PIN”code”An
also
1111PIN”code”12,An
nnn = 000 - 399 or
nnn - optional
An = A0 - A9
code = 4 - 8 digit
access code
1, 2 = relay to
activate
An default = all
access unless
specied,
relay setup
default = relay 1
unless specied
55 - 56
Store a temporary access code
in the next available location,
activate relays 1 and/or 2
respectively
TMP 1111TMP”code”12,Tnnn code = 4 - 8 digit
access code
1, 2 = relay to
activate
nnn = 001 - 255hrs
relay setup
default = relay 1
unless specied
56
Find an access code FDC 1111FDC”code”? code = 4 - 8 digit
access code
n/a 57
Delete an access code without
knowing it’s location
DEC 1111DEC”code”? code = 4 - 8 digit
access code
n/a 57
Delete all temporary codes DEP 1111DEP? n/a n/a 57
Free access timebands including
output setup with latch or
momentary trigger
FRE 1111FREn”HHMMHHMM”,days:m:o n = 0 - 9
HHMMHHMM
days = Mo, Tu, We,
Th, Fr, Sa, Su, AD,
WD and WE
m = L or M
o = RL, A1 or A2
57 - 58
Clear all free access timebands FRD 1111FRD? n/a n/a 58
Disable (1) or enable (2) speech
board
SBM 1111SBMnn? nn = 01 or 02 02 58
Set speech board volume SBV 1111SBVnn? nn = 00 - 99 75 58
Find a telephone number FDT 1111FDT” number or ends in” n/a n/a 58 - 59
End on Last Divert EOD 1111EODnn? nn = 00 or 01 00 59
Door or Gate GAT 1111GATnn? nn = 00 or 01 01 59
Shutdown and Restart RBT 1111RBT n/a n/a 59
Simulate button press via SMS BUT 1111BUTnn nn = 01 - 50 n/a 59 - 60
Initiate a special command PRG 1111PRG(command) AT commands n/a 60
AT command to send at start up AT1 1111AT1”ATxxxxxx”? Any AT command n/a 60
AT command to send at start up AT2 1111AT2”ATxxxxxx”? Any AT command n/a 60
AT command to send at start up AT3 1111AT3”ATxxxxxx”? Any AT command n/a 60
Enable extended output time EXO 1111EXOnn? nn = 81 - 87 or
32 disabled
32 60
Obtain the GSM’s IMEI number IME 1111IME? n/a n/a 61
OPTIONAL DATA
The optional data will vary depending on the command used. It may be a telephone number, a time
setting or may not be used at all. For more information refer to the following command settings.
OPTIONAL ?
Most of the commands support the ? feature. When this is added to the end of the text message, a
conrmation text message will be sent back to the sender indicating the new data has been received
and stored.
When sending text messages there may be a delay from when you send the message to when it is received by the GSM PRO
depending on how congested the network is. If you are at the intercom panel when sending the message you will hear a single
beep from the GSM PRO intercom to indicate it has received the message.
STORING THE CALL BUTTON TELEPHONE NUMBERS STN, STD, STE AND STF
Telephone numbers can be stored for the 50 available call buttons. Each call button can call up to four telephone numbers (if the
rst is busy or not answered in a certain time it can call a 2nd, 3rd and 4th number if the divert facility is setup). The STN code stores
the rst number called (primary telephone number) when the button is pressed. The STD, STE and STF codes stores the diverted
telephone numbers if the rst is busy or not answered (the GSM PRO intercom will divert to the 2nd number then divert to the 3rd
number and nally the 4th number). The messages to store/check numbers are as follows (replace STN with STD, STE or STF when
storing/checking divert numbers).