Viessmann VITORONDENS 200-T - Flue, Flexible, System Size 80 and 100 (Components) (Type B; Plastic (Pps) Flue Pipe for Routing the Flue over External Walls

Flue, flexible, system size 80 and 100 (components) (type B
23
to TRÖI 2009)
2
B
E
C
D
C
2
2
2
2
4
2
5
3
E
9
1
E
A
7
6
8
Illustration with the Vitoladens 300-C
A
Ventilation air aperture, min. 150 cm
2
or 2 × 75 cm
2
B
Flue gas
C
Inspection port
D
Connection piece = ¼ of the vertical length or max. 3 m
E
Secondary ventilation
Note
Install the flexible flue with a maximum offset of 45° from the vertical.
Rated heating output (kW) up to
35.4
from
42.8
System size
Ø mm
1
Boiler flue connection (part of the stand-
ard boiler delivery)
80 100
2
Standard shaft pack (PPs, flexible)
Comprising:
– Support bend
– Support rail
– Shaft cover (PPs)
– Spacers (5 pce, max. clearance 2 m)
or
80 100
Standard shaft pack (metal/PPs, flexi-
ble)
For twin flue chimneys; one flue for solid
fuel boilers.
Comprising:
– Support bend
– Support rail
– Shaft cover (metal)
– Terminal pipe (stainless steel)
– Spacers (5 pce, max. clearance 2 m)
80 100
Spacers (5 pce, max. clearance 2 m) 80 100
3
Flue pipe, flexible, as a 12.5 or 25 m roll 80 100
4
Connection piece for connecting residual
lengths of the flexible flue
80 100
Pipe lowering attachment with 25 m
rope
80 100
5
Inspection piece, straight (1 pce) for
installation into the flexible flue
80 100
6
Inspection piece, straight (1 pce) 80 100
7
Ventilation bezel (1 pce) 80 100
8
Pipe
1 m long (1 pce)
0.5 m long (1 pce)
80 100
9
Bend
87º (1 pce)
45º (2 pce)
or
80 100
Inspection bend 87º (1 pce) — 100
Inspection tee 87º (1 pce) 80 —
Stainless steel extension, 380 mm long
for shaft cover, metal/PPs, flexible
80 100
Max. total flue length: 18 m
The following components are taken into consideration for the maxi-
mum flue lengths:
■
Connection pipe D 0.5 m long.
■ 1 bend 87º and 1 support bend 87º
or
■ 2 bends 45º and 1 support bend 87º
Subtract other bends, tees and extension pieces from the maximum
length using the following values:
■ Connection pipe 0.5 m long: 0.5 m
■ Connection pipe 1 m long: 1 m
■ Bend 45º: 0.3 m
■ Bend 87º: 0.5 m
■ Inspection tee: 0.3 m
2.6 Plastic (PPs) flue pipe for routing the flue over external walls (type B
23
to TRÖI 2009)
The Vitoladens may also be connected, without shaft, to a flue pipe
that is routed over an external wall.
Design and sizing information for the Vitoladens 300-C, -T, and Vitorondens 200-T, 222-F
(cont.)
VITOLADENS, VITORONDENS
VIESMANN
23
5822 452 GB
2