Water Right Sanitizer Plus Series - User Manual

Water Right Sanitizer Plus Series

36 pages

To Next Page

To Next Page

Loading...

Impression Plus Series

®

Sanitizer Plus Series

®

Twin Water Softeners

For Models:

• IMP-844TW • ASP1-1044TW

• IMP-1044TW • ASP1-1054TW

• IMP-1054TW • ASP1-1354TW

• IMP-1354TW • ASP1-1465TW

• IMP-1465TW • ASP1-1665TW

• IMP-1665TW

• IMPRC-1054TW • ASP2-1044TW

• IMPRC-1354TW • ASP2-1054TW

• ASP2-1354TW

• ASP2-1465TW

• ASP2-1665TW

Table of Contents

Questions and Answers

P
Patrick DavisDec 1, 2025
What does error E3 mean on my Water Right Sanitizer Plus and how do I fix it?
- P
  Peter GoodmanDec 1, 2025
  If your Water Right Water Dispenser displays error E3, Err – 1003, or Err – 103, it means the control valve motor ran too long without finding the next cycle position. Here's what to do: * Check motor connections: Then, press the NEXT and REGEN buttons for 3 seconds to resynchronize software with piston position or disconnect power supply from PC board for 5 seconds and then reconnect. * Replace piston and stack assemblies: If foreign matter has built up, creating friction, replace the piston and stack assemblies. Then, press the NEXT and REGEN buttons for 3 seconds to resynchronize software with piston position or disconnect power supply from PC board for 5 seconds and then reconnect. * Ensure proper drive bracket seating: Snap the drive bracket in properly so that the reduction ge...
D
Dr. James PierceDec 1, 2025
What does error code 106 mean on a Water Right Water Dispenser?
- N
  nicholas29Dec 1, 2025
  If your Water Right Water Dispenser displays error Err – 1006, Err – 106, or Err – 116, it means the MAV/ SEPS/ NHBP/ AUX MAV valve motor ran too long and couldn't find the proper park position. Here's what to check: * Check control valve programming: If the control valve is programmed for ALT A or B, nHbP, SEPS, or AUX MAV without a MAV or NHBP valve attached, press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position or disconnect the power supply from the PC board for 5 seconds and then reconnect, then reprogram the valve to the proper setting. * MAV/NHBP motor wire connection: Connect the MAV/NHBP motor to the PC board two-pin connection labeled DRIVE. Then, press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with...
S
stephanie88Dec 1, 2025
What does error 107 mean on Water Right Sanitizer Plus Water Dispenser?
- L
  Laura FowlerDec 1, 2025
  If you're getting error Err – 1007, Err – 107, or Err – 117 on your Water Right Water Dispenser, it means the MAV/ SEPS/NHBP/AUX MAV valve motor ran too short and stalled while trying to find the proper park position. Here's what you can do: * Check for foreign material in the MAV/NHBP valve: Open up the MAV/NHBP valve and check the piston and seal/stack assembly for any foreign material. Then, press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position or disconnect the power supply from the PC board for 5 seconds and then reconnect. * Inspect for mechanical binding: Check the piston and seal/stack assembly, reduction gears, drive gear interface, and the MAV/NHBP black drive pinion on the motor for being jammed into the motor body. Then, pres...
D
donaldnealAug 28, 2025
Why is the time of day flashing on my Water Right Sanitizer Plus Water Dispenser?
- J
  Jared FieldsAug 28, 2025
  If the time of day display is flashing on and off on your Water Right Water Dispenser, it could indicate: * A power outage: Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A broken drive gear or drive cap assembly: Replace the drive gear or drive cap assembly. * A broken piston rod: Replace the piston rod. * A defective PC board.
V
Victoria MaciasSep 3, 2025
Why Water Right Sanitizer Plus doesn't regenerate automatically unless the buttons are pressed?
- J
  jessica56Sep 3, 2025
  If your Water Right Water Dispenser control valve does not regenerate automatically but does when you depress and hold the correct buttons, ensure the bypass valve is not in the bypass position by turning the bypass handles to the service position. Check that the meter is connected to the meter connection on the PC board and that the meter cable wires are securely installed into the three pin connector labeled METER. Remove the meter to check for rotation or foreign material that may be causing a restricted or stalled meter turbine. Verify the programming is correct. If these steps do not solve the problem, the meter or PC board may be defective and require replacement.
J
james73Sep 2, 2025
What to do if Water Right Sanitizer Plus Water Dispenser delivers hard or untreated water?
- R
  Robert GreeneSep 2, 2025
  If you have hard or untreated water being delivered by your Water Right Water Dispenser, the bypass valve may be open or faulty, requiring you to fully close or replace it. High water usage can exhaust the media, so check program settings or diagnostics for abnormal usage. Also, inspect the meter for proper registration and any obstructions. Ensure there's an adequate level of regenerant in the tank and that the control is drawing it in correctly. Check the refill setting and flow control for any issues. If problems persist, the seal/stack assembly may be damaged, the media bed fouled, or the control valve and piston types mismatched, all of which would require replacement.
L
Lauren WadeSep 2, 2025
Why does Water Right Water Dispenser control valve regenerates at wrong time of day?
- G
  ginawilliamsSep 2, 2025
  If your Water Right Water Dispenser control valve regenerates at the wrong time, it might be due to a power outage, which requires resetting the time of day. Also, verify that the time of day and regeneration time are set correctly. Ensure the control valve is not set to 'on 0' or 'NORMAL + on 0'; it should be set to 'NORMAL' for delayed regeneration.
J
Jordan MedinaSep 1, 2025
What to do if display does not indicate that water is flowing in Water Right Sanitizer Plus Water Dispenser?
- R
  Robert NicholsSep 1, 2025
  If the display on your Water Right Water Dispenser doesn't indicate water flow, first ensure the bypass handles are correctly positioned for service. Then, check if the meter is properly connected to the PC board's meter connection. Also, verify that the meter cable wires are securely installed into the three-pin connector labeled 'METER'. Finally, examine the meter for any obstructions or rotation issues. If these steps don't resolve the issue, the meter or PC board might be defective and require replacement.
A
Angela BrownSep 1, 2025
What does Err – 400 mean on my Water Right Sanitizer Plus?
- C
  Caitlin PageSep 1, 2025
  If your Water Right Water Dispenser is showing Err – 400* Memory Errors, the cause may be: * Depleted Battery: See Operating Display and Maintenance section. * Defective PC Board: Replace PC board.
A
alvareztonyaAug 31, 2025
What does Err – 204 mean on my Water Right Water Dispenser?
- G
  Gregory RussellSep 1, 2025
  If your Water Right Water Dispenser displays Err – 204, it means a leak has been detected. This occurs when the dP input is active for “ALARM” and the input is closed. The alarm buzzer will activate, and the screen will display the error. Check for a low flow leak. Press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC Board for 5 seconds and then reconnect to clear the error.

Water Right Sanitizer Plus Series Specifications

General

Brand	Water Right
Model	Sanitizer Plus Series
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

Bypass Valve Operation

Installation Procedures

General Installation and Service Warnings

General guidelines and warnings for installation and service procedures.

Site Requirements

Technical specifications for the installation site.

Well Water Installation

Specific installation instructions for well water systems.

Municipal Installation

Specific installation instructions for municipal water systems.

Programming Procedures

Set Time of Day

Procedure for setting the current time of day on the unit.

Programming Settings

Instructions for adjusting various programming settings.

Start-Up Instructions

Flushing of System

Steps to flush the system of debris and air after installation.

Conditioning of Media

Procedure to condition the media after installation.

Sanitizing of Unit

Operating Displays and Maintenance

General Operation Displays

Regeneration Modes

Explanation of how the twin system regenerates.

Manual Regeneration

Instructions for initiating regeneration manually.

Power Loss and Battery Replacement

Salt Indicator and Error Handling

Troubleshooting Guide

Service Instructions

Transfer Cap Assemblies Service

Related product manuals

Sanitizer Plus ASP1-1054

Sanitizer Plus ASP2-1054

Sanitizer Plus ASP1-1354

Water Right Sanitizer Plus

Water Right IM-1054

Water Right IMP-1035

Water Right IMP-1054

Water Right ISP2-1354

Water Right ISP2-1054

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression Series

Water Right Impression Series

Preview: Impression Plus Series

Impression Plus Series