Water Right Sanitizer Plus Series - User Manual

Water Right Sanitizer Plus Series

36 pages

To Next Page

To Next Page

Loading...

Impression Plus Series

®

Sanitizer Plus Series

®

Twin Water Softeners

For Models:

• IMP-844TW • ASP1-1044TW

• IMP-1044TW • ASP1-1054TW

• IMP-1054TW • ASP1-1354TW

• IMP-1354TW • ASP1-1465TW

• IMP-1465TW • ASP1-1665TW

• IMP-1665TW

• IMPRC-1054TW • ASP2-1044TW

• IMPRC-1354TW • ASP2-1054TW

• ASP2-1354TW

• ASP2-1465TW

• ASP2-1665TW

Table of Contents

Questions and Answers

P
Patricia EdwardsAug 30, 2025
What does error E4 mean on my Water Right Water Dispenser?
- U
  uflowersAug 30, 2025
  If you're seeing error E4, Err – 1004, or Err – 104 on your Water Right Water Dispenser, it means the control valve motor ran too long trying to reach the home position. Make sure the drive bracket is properly snapped in so that the reduction gears and drive gear interface correctly. Then, press the NEXT and REGEN buttons for 3 seconds to resynchronize software with piston position or disconnect power supply from PC board for 5 seconds and then reconnect.
S
Sherry Savage DDSAug 28, 2025
Why won't my Water Right Sanitizer Plus Water Dispenser draw in regenerant?
- B
  Brittany DavisAug 29, 2025
  If the control valve on your Water Right Water Dispenser isn't drawing in regenerant, consider the following: * The injector might be plugged: Remove and clean or replace the injector. * The regenerant piston could be faulty: Replace the regenerant piston. * There might be a leak in the regenerant line connection: Inspect the regenerant line for air leaks. * The drain line might be restricted, causing excess back pressure: Inspect the drain line and clean to correct the restriction. * The drain line might be too long or too high: Shorten the length or height. * The water pressure might be low: Check the incoming water pressure, which must remain at a minimum of 25 psi.
J
Jeffery AdamsSep 3, 2025
How to fix no display on Water Right Water Dispenser PC board?
- T
  Tammy CarpenterSep 3, 2025
  If the display on the PC board of your Water Right Water Dispenser is blank, verify that the electric outlet has power and use a working outlet if necessary. Ensure the control valve power adapter is plugged into the outlet and connected to the PC board. Confirm the power supply is delivering the correct voltage to the PC board. If these steps don't resolve the issue, the power adapter or PC board may be defective and require replacement.
J
jennifer51Aug 28, 2025
Why is my Water Right Sanitizer Plus delivering residual regenerant?
- S
  Sharon YangAug 28, 2025
  If your Water Right Water Dispenser is delivering residual regenerant, check these potential causes: * Low water pressure: Ensure incoming water pressure remains at a minimum of 25 psi. * Incorrect, damaged, or restricted injector: Replace the injector with the correct size for your application. * Restricted drain line: Inspect the drain line for any restrictions or debris and clean it.
M
Matthew ReedAug 27, 2025
Why doesn't my Water Right Water Dispenser display water flow?
- M
  Megan BrownAug 27, 2025
  If the display on your Water Right Water Dispenser isn't showing that water is flowing, consider these possible issues: * Bypass valve position: Turn bypass handles to place bypass in service position. * Meter connection: Connect meter to the three pin connection labeled METER on PC board. * Restricted meter turbine: Remove meter and check for rotation or foreign material. * Meter wire installation: Verify meter cable wires are installed securely into three pin connector labeled METER. * Defective meter: Replace meter. * Defective PC board: Replace PC board.
H
hannahfreemanAug 27, 2025
Why is the time of day wrong on my Water Right Water Dispenser PC board?
- J
  Jill HolmesAug 27, 2025
  If the PC board on your Water Right Water Dispenser isn't showing the correct time, it might be due to: * The power adapter being plugged into an outlet controlled by a light switch: Use an uninterrupted outlet. * A tripped breaker switch or GFI: Reset the breaker switch or GFI switch. * A power outage: Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A defective PC board: Replace the PC board.
M
Matthew MillerAug 27, 2025
Why is water constantly running to the drain in my Water Right Sanitizer Plus Water Dispenser?
- A
  Allison MarshallAug 27, 2025
  If water is constantly running to the drain in your Water Right Water Dispenser, it could be due to: * A power outage during regeneration: Upon power restoration, the control will finish the remaining regeneration time. Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A damaged seal/stack assembly: Replace the seal/stack assembly. * Piston assembly failure: Replace the piston assembly. * The drive cap assembly not being tightened properly: Retighten the drive cap assembly.
P
Patricia SolisAug 27, 2025
Why is my Water Right Sanitizer Plus Water Dispenser using too much regenerant?
- J
  Joshua JohnsonAug 27, 2025
  If your Water Right Water Dispenser control valve is using too much regenerant, consider these possible causes: * Improper refill setting: Check the refill setting. * Improper program settings: Ensure the program settings are specific to the water quality and application needs. * Frequent regeneration: Check for leaking fixtures that may be exhausting capacity or the system is undersized.
R
Ryan GutierrezAug 26, 2025
Why is there excessive water in my Water Right Sanitizer Plus Water Dispenser's regenerant tank?
- M
  Melissa SimonAug 26, 2025
  If there's too much water in the regenerant tank of your Water Right Water Dispenser, here are possible causes: * Improper program settings: Check the refill setting. * Plugged injector: Remove and clean or replace the injector. * Drive cap assembly not tightened properly: Retighten the drive cap assembly. * Damaged seal/stack assembly: Replace the seal/stack assembly. * Restricted or kinked drain line: Check the drain line for restrictions or kinks and correct them. * Plugged backwash flow controller: Remove and clean or replace the backwash flow controller. * Missing refill flow controller: Replace the refill flow controller.
M
Matthew WilliamsAug 25, 2025
Why does my Water Right Water Dispenser regenerate at the wrong time?
- Q
  qpriceAug 26, 2025
  If your Water Right Water Dispenser control valve is regenerating at the wrong time, here's what could be happening: * **Power Outage:** Reset the time of day. If your PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * **Incorrect Time of Day Setting:** Reset the time of day to the correct time. * **Incorrect Regeneration Time Setting:** Reset the regeneration time. * **Control Valve Set to Immediate Regeneration:** Check the programming setting and reset to NORMAL for a delayed regeneration time. * **Control Valve Set to Both Delayed and Immediate Regeneration:** Check the programming setting and reset to NORMAL for a delayed regeneration time.

Water Right Sanitizer Plus Series Specifications

General

Brand	Water Right
Model	Sanitizer Plus Series
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

Bypass Valve Operation

Installation Procedures

General Installation and Service Warnings

General guidelines and warnings for installation and service procedures.

Site Requirements

Technical specifications for the installation site.

Well Water Installation

Specific installation instructions for well water systems.

Municipal Installation

Specific installation instructions for municipal water systems.

Programming Procedures

Set Time of Day

Procedure for setting the current time of day on the unit.

Programming Settings

Instructions for adjusting various programming settings.

Start-Up Instructions

Flushing of System

Steps to flush the system of debris and air after installation.

Conditioning of Media

Procedure to condition the media after installation.

Sanitizing of Unit

Operating Displays and Maintenance

General Operation Displays

Regeneration Modes

Explanation of how the twin system regenerates.

Manual Regeneration

Instructions for initiating regeneration manually.

Power Loss and Battery Replacement

Salt Indicator and Error Handling

Troubleshooting Guide

Service Instructions

Transfer Cap Assemblies Service

Related product manuals

Sanitizer Plus ASP1-1054

Sanitizer Plus ASP2-1054

Sanitizer Plus ASP1-1354

Water Right Sanitizer Plus

Water Right IM-1054

Water Right IMP-1035

Water Right IMP-1054

Water Right ISP2-1354

Water Right ISP2-1054

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression Series

Water Right Impression Series

Preview: Impression Plus Series

Impression Plus Series