Model
2001
SECTION
2
INSTALLATION
2.1 MECHANICAL INSTALLATION
2.1
.I
Initial Inspection
After unpacking the instrument, visually inspect the
external parts for damage to knobs, connectors, surface
areas, etc. The shipping container and packing material
should be saved in case it is necessary to reship the unit.
2.1.2
Damage Claims
If the instrument is received mechanically damaged in
transit, notify the carrier and either the nearest Wavetek
area representative or the factory in Indiana. Retain the
shipping carton and packing material for the carrier's
inspection.
The local representative, or the factory, will immediately
arrange for either the replacement or repair of your in-
strument, without waiting for damage claim settlements.
2.1.3
Rack Mounting
The instrument is
1 /2
racksize and two rack mounting
kits are available. The
K-103
kit provides the necessary
hardware to mount the unit to either
tlie right or left of
a standard
5%"
x
19"
opening. The
K- 104
kit provides
the necessary hardware to rack mount two instruments.
These may be two
1000
or
2000
series Wavetek, Indi-
ana Instruments, or two
130
or
140
series Wavetek,
San
Diego Instruments, or a combination of either. This
provides a
7"
x
19"
package. Facilities are provided for
Front Panel mounting of instrument Rear Panel con-
nectors.
2.1.4 K-103,
Rack Mounting Kit (Refer to Figure
2-1
)
CONTENTS
Item
Qty. Part No.
A
(Side)
1
ea.
8000-608
B
(Side)
1
ea.
COOO-691
C
(Screw)
8
ea.
HS101-806
Procedure:
Remove the screws from one side panel at a time. Mount
item
A
or
B
against the side panel of the instrument and
secure with screws provided (item
C).
Repeat operation
for other side. NOTE: Items
A
&
B
may be interchanged
to position the unit to the side of the rack desired.
Figure
2-1.
K-103
Rack
Mounting
Model
2001
2.1
MECHANICAL INSTALLATION
2.1.1 I nitial Inspection
After unpacking the instrument, visually inspect the
external parts for damage to knobs, connectors, surface
areas, etc. The shipping container and packing material
should be saved in case it is necessary
to
reship the unit.
2.1.2 Damage Claims
If
the
instrument is received mechanically damaged in
transit,
notify
the carrier and either
the
nearest Wavetek
area representative or
the
factory in Indiana. Retain the
shipping carton and packing material
for
the
carrier's
inspection.
The loca! representative,
or
the
factory,
will
immediately
arrange
for
either the replacement or repair
of
your
in-
strument,
without
waiting
for damage claim settlements.
2.1.3 Rack
Mounting
The instrument
is
1/2
rack. size and
two
rack
mounting
kits
are
available. The
K-1
03
kit
provides
the
necessary
hardware
to
mount
the
unit
to either
the
right or left
of
a standard 5;4" x
19"
opening. The K·1
04
kit
provides
A
..
--
..
--
2
SECTION
INSTALLATION
the necessary hardware
to
rack
mount
two
instruments.
These may be
two
1000
or
2000
series Wavetek,
Indi-
ana Instruments,
or
two
130 or
140
series Wavetek,
San Diego Instruments, or a
combination
of
either. This
provides a
7"
x
19"
package. Facilities are provided for
Front Panel
mounting
of
instrument Rear Panel
con-
nectors.
2.1.4 K-103, Rack
Mounting
Kit (Refer
to
Figure
2-1)
CONTENTS
Item Qty.
Part No.
A
(Side)
1
ea.
BOOO-608
B
(Side)
1 ea.
COOO-691
C
(Screw)
8
ea.
HS1
01
-806
Procedure:
Remove
the
screws from one side panel at a time.
Mount
item A or B against
the
side panel
of
the instrument and
secure
with
screws provided (item C). Repeat operation
for other side. NOTE: Items A
& B may
be
interchanged
to
position the
unit
to the side
of
the rack desired.
B
-
l"
--
...
Figure 2-1. K-103 Rack
Mounting
2-1
To Next Page
Loading...
