Yaesu VX-3E - Page 29

132 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

VX-3R/E OPERATING MANUAL 27

REPEATER OPERATION

NOTE

Table of Contents

Table of Contents2
General Description3
Controls & Connections4
- Keypad Functions5
- LCD Display6
Accessories & Options7
- Antenna Installation8
- Installation of FNB-82LI Battery Pack8
Installation of Accessories9
- Battery Charging9
- Installation of FBA-37 Alkaline Battery Case10
- Battery Life Information10
Interface of Packet Tncs11
Operation12
- Switching Power on and off12
- Adjusting the Volume Level12
- Squelch Adjustment13
- Selecting the Operating Band14
- Frequency Navigation15
- Transmission16
- AM and FM Broadcast Reception17
  - SUB-RX Operation18
Advanced Operation20
- Keyboard Locking20
- Adjusting the Keypad Beeper Volume Level21
- Keypad/Lcd Illumination22
- Checking the Battery Voltage22
- Changing the Channel Steps23
- Changing the Receiving Mode23
- S-Meter Squelch24
- Checking the Temperature25
Repeater Operation26
- Repeater Shifts26
- Automatic Repeater Shift (ARS)26
- Manual Repeater Shift Activation27
  - Changing the Default Repeater Shifts27
- Tone Calling (1750 Hz)28
- Checking the Repeater Uplink (Input) Frequency28
CTCSS/DCS/EPCS Operation30
- CTCSS Operation30
- DCS Operation32
  - DCS Code Inversion33
- Tone Search Scanning34
- EPCS (Enhanced Paging & Code Squelch)36
- CTCSS/DCS/EPCS Bell Operation39
  - Programming the User Beep40
- Split Tone Operation41
Memory Mode43
- Regular Memory Channel Operation44
- Special Memory Channel Operation53
Scanning56
- Setting the Scan-Resume Mode56
- VFO Scanning58
- Memory Scanning60
- Programmable Band Limit Memory Scan Pms64
- Priority Channel Scanning Dual Watch65
  - Priority Revert Mode66
- Automatic Lamp Illumination on Scan Stop67
- Band Edge Beeper67
Smart Search Operation68
- Setting the Smart Search Mode68
- Storing Smart Search Memories69
Channel Counter Operation70
- Setting the Channel Counter Sweep Width71
Message Feature72
- Programming a Message72
- Programming a Member List73
- Set Your Personal ID74
- Sending a Messages74
- Receiving a Message75
Emergency Feature76
- Emergency Channel Operation76
- Emergency Automatic ID Eai Feature77
ARTS (Automatic Range Transponder System)80
- Basic ARTS Setup and Operation81
- ARTS Polling Time Options81
- ARTS Alert Beep Options82
- CW Identifier Setup83
Srg "Sister Radio Group " Mode84
Internet Connection Feature84
FRG ("Friendly Radio Group") Mode85
- Programming the FRG Code85
- Operation Accessing an Frg Node86
DTMF Operation87
- Manual DTMF Tone Generation87
- DTMF Autodialer87
CW Learning Feature90
CW Training Feature92
Miscellaneous Setting93
- Password93
- Programming the [ ] Key94
  - Assign the Set Mode Item to the [ ] Key94
- ATT (Front End Attenuator)95
- Receive Battery Saver Setup95
- Wakeup Feature96
- TX Battery Saver97
- Disabling the BUSY Indicator97
- Automatic Power-Off (APO) Feature98
- Transmitter Time -Out Timer Tot99
- Automatic Power-On Feature100
- Busy Channel Lock -Out Bclo100
- Changing the TX Deviation Level101
- Changing the Microphone Gain101
- My Bands Operation102
- Changing the Status of the [ ] Key103
Cloning104
Set Menu Mode105
Reset Procedures127
Specifications128
FCC Notice130
Declaration of Conformity131

Related product manuals

Preview: Yaesu VX-3R

Preview: Yaesu VX-7R

Preview: Yaesu VX-6R

Preview: Yaesu VX-8R

Preview: Yaesu VX-150

Preview: Yaesu VX-170

Preview: Yaesu VX-8GR

Preview: Yaesu VX-8DR

Preview: Yaesu VX-246

Preview: Yaesu VX-7R - TECHNICAL

Yaesu VX-7R - TECHNICAL