i-1
Index
A.
Abbreviation ................................................0-5
Active test ...................................................4-3
Adjusting the forward gear shim (T1)
thickness .................................................8-54
Adjusting the reverse gear shim (T1)
thickness .................................................8-95
Adjusting the reverse gear shim (T2)
thickness ........................................8-57, 8-91
Adjusting the trim sensor ..........................9-29
Adjusting the valve clearance .....................7-4
After test run .............................................10-7
Assembling the cylinder block...................7-90
Assembling the cylinder head ...................7-60
Assembling the drive shaft...............8-25, 8-78
Assembling the forward gear ....................8-27
Assembling the fuel filter assembly...........6-12
Assembling the gear pump assembly .......9-49
Assembling the lower case ..............8-27, 8-79
Assembling the oil pan and exhaust
manifold ..................................................9-20
Assembling the oil pump assembly...........7-67
Assembling the oil seal housing.......8-28, 8-79
Assembling the
propeller .......................... 8-4, 8-8, 8-64, 8-67
Assembling the propeller shaft
assembly.................................................8-18
Assembling the propeller shaft housing
assembly.................................................8-19
Assembling the propeller shaft housing
assembly and forward gear.....................8-74
Assembling the PTT motor .......................9-42
Assembling the reverse gear ...........8-19, 8-78
Assembling the shift actuator assembly....7-35
Assembling the starter motor ....................5-61
Assembling the tilt ram..............................9-55
Assembling the trim ram ...........................9-56
Assembling the upper case.......................9-16
Assembling the vapor separator ...............6-40
Assembling the water pump
housing ..........................................8-12, 8-70
Asynchronous fuel injection ........................2-7
B.
Basic ignition timing ....................................2-9
Battery installation.....................................3-15
Battery requirement ....................................1-7
Battery wiring with house (accessory)
battery .....................................................3-17
Battery wiring without house (accessory)
battery .....................................................3-15
Bleeding the PTT unit ...............................9-35
Bottom cowling .................................. 5-8, 5-16
Bracket unit........................................ 1-5, 1-28
Bracket unit technical data ....................... 1-25
Break-in .................................................... 10-7
C.
Calculated value (B) table ............... 8-46, 8-88
Camshaft .................................................. 7-42
Canister .................................................... 6-25
Changing the engine oil............................ 10-8
Changing the gear oil ............................. 10-10
Charging system.............................. 1-14, 2-18
Charging unit and starting unit....................A-9
Charging units and component................. 5-40
Checking the air pressure sensor............. 5-49
Checking the air temperature sensor ....... 5-48
Checking the anode.................................. 10-7
Checking the armature (PTT motor)......... 9-41
Checking the armature (starter motor) ..... 5-60
Checking the battery........................ 10-3, 10-7
Checking the brush................................... 9-41
Checking the brush holder........................ 5-61
Checking the cam position sensor............ 5-29
Checking the camshaft ............................. 7-47
Checking the canister ............................... 6-26
Checking the canister check valve ........... 6-26
Checking the check valve......................... 6-40
Checking the clamp bracket anode .......... 9-27
Checking the communication between
the engine and the Digital
Electronic Control ................................... 10-4
Checking the compression pressure .......... 7-1
Checking the connecting rod big end side
clearance ................................................ 7-80
Checking the connecting rod small end inside
diameter and big end inside diameter .... 7-80
Checking the cooling water passage........ 10-7
Checking the cooling water pilot hole ....... 10-3
Checking the crankcase bolt .................... 7-81
Checking the crankpin oil clearance......... 7-82
Checking the crankshaft ........................... 7-81
Checking the crankshaft journal oil
clearance ................................................ 7-86
Checking the cylinder block anode........... 7-90
Checking the cylinder bore ....................... 7-78
Checking the cylinder head ...................... 7-55
Checking the cylinder head anode ........... 7-60
Checking the cylinder head bolt ............... 7-56
Checking the dog clutch .................. 8-18, 8-74
Checking the drive shaft .................. 8-25, 8-78
Checking the drive shaft bushing ............. 9-16
Checking the electrical component........... 5-21
Checking the engine ECM circuit ............. 5-23
Index i
To Next Page
Loading...
