EasyManuals Logo

Yealink SIP-T58A User Manual

Yealink SIP-T58A
375 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #322 background imageLoading...
Page #322 background image
User Guide for SIP-T58V/A Smart Media Phone
322
Transfer a call to the monitored user.
Pick up an incoming call of the monitored user.
Placing a Call to the Monitor User
You can tap a BLF key to dial out the monitored phone number when the monitored line is idle.
To place a call to the monitored user when the IP phone is idle:
1. Tap the BLF key.
The IP phone dials out the phone number of the monitored user.
Transferring a Call to the Monitored User
When there is already an active call on the IP phone, you can transfer the active call to the
monitored user by tapping the BLF key. The phone handles the active call differently depending
on the configuration of the transfer mode via Dsskey with the BLF key (refer to Configuring
Transfer Mode via DssKey). The transfer mode via Dsskey has the following modes:
Blind Transfer
Attended Transfer
New Call
To perform a blind transfer:
When the transfer mode via Dsskey is set to Blind Transfer and there is already an active call on
the IP phone, you can do the following:
1. Tap the BLF key of the monitored user which you want to transfer this call to.
Then the active call is connected to the number of the monitored user.
To perform a semi-attended transfer:
When the transfer mode via Dsskey is set to Attended Transfer and there is already an active
call on the IP phone, you can do the following:
1. Tap the BLF key of the monitored user which you want to transfer this call to. The phone
will dial the number of the monitored user.
2. Tap the BLF key of the monitored user again or the Transfer soft key to complete the
transfer when receiving ringback.
To perform an attended transfer:
When the transfer mode via Dsskey is set to Attended Transfer and there is already an active
call on the IP phone, you can do the following:
1. Tap the BLF key of the monitored user which you want to transfer this call to. The phone
will dial the number of the monitored user.
2. Tap the BLF key of the monitored user again or the Transfer soft key to complete the
transfer after the monitored user answers the call.

Table of Contents

Other manuals for Yealink SIP-T58A

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T58A and is the answer not in the manual?

Yealink SIP-T58A Specifications

General IconGeneral
Touchscreen typeCapacitive
Display resolution1024 x 600 pixels
Operating system version5.1.1
Operating system installedAndroid
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
BluetoothNo
Security algorithmsSRTP
Networking standardsIEEE 802.1x
Ethernet LAN interface typeGigabit Ethernet
Supported network protocolsFTP/TFTP/HTTP/HTTPS, IPv4/IPv6, UDP/TCP/DNS-SRV
USB 2.0 ports quantity2
Voice codecsG.711Mu, G.711a, G.722, G.722.1, G.722.1C, G.723, G.726, G.729ab, iLBC
Lines quantity- lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Front camera resolution (numeric)2 MP
Base station keys27
AC adapter input voltage100 - 240 V
AC adapter output current2 A
Power consumption (typical)1.9 W
Operating temperature (T-T)-10 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Cables includedLAN (RJ-45)
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Depth220 mm
Width259.4 mm
Height239 mm
Package depth293 mm
Package width324 mm
Package height128 mm

Related product manuals