Yueming CMA1325C-B-A - User Manual

Questions and Answers

M
Michelle HillAug 13, 2025
What to do if my Yueming CMA1325C-B-A Printer laser tube can't work?
- S
  Stacy Ward MDAug 13, 2025
  If the laser tube of your Yueming Printer isn't working, there could be several reasons: * The water-cooling system might not be on. In that case, turn on the water circulation system. * The water protection may not be triggered. Check if the chiller is working properly. * The laser system might not be turned on. Press the laser power button. * The laser power supply could be damaged. Replace it with a switching power supply of the same specifications. * The laser itself may be damaged. If so, replace the laser.
C
Carla HendersonAug 17, 2025
What to do if cutting graphics and drawing size do not match on Yueming CMA1325C-B-A?
- E
  Elizabeth MorrisAug 17, 2025
  If the cutting graphics and drawing size do not match on your Yueming Printer, consider the following: * There might be a program input error. Check the procedures according to the figure. * The synchronous belt could be loose. Tension the synchronous belt. * The control system might be damaged. Check the stepper motor and drive, and replace if damaged.
S
Sandy LopezAug 21, 2025
What to do if my Yueming CMA1325C-B-A gives equipment alarm?
- J
  jesus91Aug 21, 2025
  If your Yueming Printer is showing an equipment alarm, check the following: * Confirm if the motherboard parameters are correct, and correct them if necessary. * Check the alarm signal source of the equipment.
T
Troy EdwardsAug 25, 2025
Why is the figure size wrong on my Yueming CMA1325C-B-A?
- S
  Stephanie RodriguezAug 25, 2025
  If the figure size is wrong on your Yueming Printer, there may be a few reasons: * If using PLT output in CorelDraw, ensure the plotter unit in the page option is set correctly to match the resolution of the SmartCarve software's lead-in PLT option. * If using PLT output in CorelDraw, verify that the zooming in the page option is set to 100%, and change it to 100% if it is not. * Check if the resolution of the mainboard parameters are correct, and set them to the correct resolution or equivalent. * Ensure the mainboard is properly grounded to eliminate interference. * If the mainboard is crashing due to high temperature, take measures to lower the temperature.
C
Christina GriffinAug 28, 2025
What to do if the Yueming CMA1325C-B-A Printer laser pauses during working?
- M
  Mary PerezAug 28, 2025
  If the laser pauses during working on your Yueming Printer: * Clean the water tank and dredge the water hose to ensure proper water flow. * Install a stabilizer to the input power supply to maintain consistent power.
M
Mia RandallSep 1, 2025
How to fix fail in movement of motor shaft or twittering of it during movement in Yueming CMA1325C-B-A?
- J
  Joseph CohenSep 1, 2025
  If the motor shaft fails to move or twitters during movement in your Yueming Printer: * Ensure that the motor parameters are set correctly. * The drive or motor may be damaged, consider changing the drive or motor. * Try reconnecting the motor and drive line.
J
Julian MoranSep 4, 2025
How to resolve reverse direction of motor shaft movement in Yueming Printer?
- G
  gibbsnicoleSep 4, 2025
  If the motor shaft movement direction is reversed in your Yueming Printer, check the electric earthing and drive parameter settings to ensure they are correct. This is especially important if the lines from the drive to the motor are connected improperly, and the drive parameter settings are correct.
M
mthomasSep 8, 2025
How to troubleshoot if my Yueming CMA1325C-B-A can’t be turned on?
- B
  Brian AyalaSep 8, 2025
  If your Yueming Printer can’t be turned on: * Release the emergency stop button. * Reset the main contactor.