Zennio FLAT - Page 51

Flat & Flat 55
http://www.zennio.com Technical Support: http://support.zennio.com
51
110
2 Bytes
I
C - - W -
DPT_Value_Tempd
-670760.00 -
670760.00
[Tx] Setpoint Offset
Float Offset Value
111
2 Bytes
O
C T R - -
DPT_Value_Temp
-273.00 - 670760.00
[Tx] Setpoint Status
Current Setpoint
112
2 Bytes
O
C T R - -
DPT_Value_Temp
-273.00 - 670760.00
[Tx] Basic Setpoint Status
Current Basic Setpoint
113
2 Bytes
O
C T R - -
DPT_Value_Tempd
-670760.00 -
670760.00
[Tx] Setpoint Offset Status
Current Setpoint Offset
114
1 Bit
I
C - - W -
DPT_Reset
0/1
[Tx] Setpoint Reset
Reset Setpoint to Default
1 Bit
I
C - - W -
DPT_Reset
0/1
[Tx] Offset Reset
Reset Offset
115
1 Bit
I
C - - W -
DPT_Heat_Cool
0/1
[Tx] Mode
0 = Cool; 1 = Heat
116
1 Bit
O
C T R - -
DPT_Heat_Cool
0/1
[Tx] Mode Status
0 = Cool; 1 = Heat
117
1 Bit
I
C - - W -
DPT_Switch
0/1
[Tx] On/Off
0 = Off; 1 = On
118
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] On/Off Status
0 = Off; 1 = On
119
1 Bit
I/O
C - R W -
DPT_Switch
0/1
[Tx] Main System (Cool)
0 = System 1; 1 = System 2
120
1 Bit
I/O
C - R W -
DPT_Switch
0/1
[Tx] Main System (Heat)
0 = System 1; 1 = System 2
121
1 Bit
I
C - - W -
DPT_Enable
0/1
[Tx] Enable/Disable Secondary System (Cool)
0 = Disable; 1 = Enable
122
1 Bit
I
C - - W -
DPT_Enable
0/1
[Tx] Enable/Disable Secondary System (Heat)
0 = Disable; 1 = Enable
123, 129
1 Byte
O
C T R - -
DPT_Scaling
0% - 100%
[Tx] [Sx] Control Variable (Cool)
PI Control (Continuous)
124, 130
1 Byte
O
C T R - -
DPT_Scaling
0% - 100%
[Tx] [Sx] Control Variable (Heat)
PI Control (Continuous)
1 Byte
O
C T R - -
DPT_Scaling
0% - 100%
[Tx] [Sx] Control Variable
PI Control (Continuous)
125, 131
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable (Cool)
2-Point Control
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable (Cool)
PI Control (PWM)
126, 132
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable (Heat)
2-Point Control
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable (Heat)
PI Control (PWM)
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable
2-Point Control
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] Control Variable
PI Control (PWM)
127, 133
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] PI State (Cool)
0 = PI Signal 0%; 1 = PI Signal Greater than 0%
128, 134
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] PI State (Heat)
0 = PI Signal 0%; 1 = PI Signal Greater than 0%
1 Bit
O
C T R - -
DPT_Switch
0/1
[Tx] [Sx] PI State
0 = PI Signal 0%; 1 = PI Signal Greater than 0%
135, 139
2 Bytes
O
C T R - -
DPT_Value_Temp
-273.00 - 670760.00
[Ix] Current Temperature
Temperature Sensor Value
136, 140
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Ix] Overcooling
0 = No Alarm; 1 = Alarm
137, 141
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Ix] Overheating
0 = No Alarm; 1 = Alarm
138, 142
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Ix] Probe Error
0 = No Alarm; 1 = Alarm
143
2 Bytes
O
C T R - -
DPT_Value_Temp
-273.00 - 670760.00
[Internal Probe] Current Temperature
Temperature Sensor Value
144
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Internal Probe] Overcooling
0 = No Alarm; 1 = Alarm
145
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Internal Probe] Overheating
0 = No Alarm; 1 = Alarm
146
1 Byte
I
C - - W -
DPT_SceneNumber
[Motion Detector] Scene Input
Scene Value
147
1 Byte
C T - - -
DPT_SceneControl
0-63; 128-191
[Motion Detector] Scene Output
Scene Value
148, 177
1 Byte
O
C T R - -
DPT_Scaling
0% - 100%
[Ix] Luminosity
0-100%
149, 178
1 Bit
O
C T R - -
DPT_Alarm
0/1
[Ix] Open Circuit Error
0 = No Error; 1 = Open Circuit Error