ABB A140-H55 - Tables

Operation Manual / 4 Product description / A130-H.. - A140-H..
Tables
Page 115 /
115
© Copyright 2015 ABB. All rights reserved.
HZTL4030_EN
Revision C
September 2015
Tables
Table 1
Related documents ...................
5
Table 2
Turbocharger weights ...............
11
Table 3
Requirements for threaded rods
17
Table 4
Tightening torques for standard
nuts ............................................
19
Table 5
Pressure screw tightening
torque ........................................
21
Table 6
Lubricating oil pressure, oil inlet
29
Table 7
Lubricating oil temperature at
the inlet ......................................
30
Table 8
Lubricating oil temperature at
the outlet ....................................
30
Table 9
Tightening torque (86505).........
34
Table 10
Expected replacement intervals
41
Table 11
Maintenance table .....................
45
Table 12
Parameters for wet cleaning of
compressor ...............................
49
Table 13
Turbine wet cleaning,
recommended operating state ..
52
Table 14
Wet cleaning of turbines,
parameters ................................
53
Table 15
Value table for soaking .............
61
Table 16
Malfunctions when starting –
Delayed start-up ........................
65
Table 17
Malfunctions when starting –
Vibrations ..................................
65
Table 18
Malfunctions when starting –
Rubbing of rotating parts ...........
65
Table 19
Malfunctions during operation –
Lubricating oil pressure too low
66
Table 20
Malfunctions during operation –
Speed reduces ..........................
66
Table 21
Malfunctions during operation –
Speed increases .......................
66
Table 22
Malfunctions during operation –
Exhaust gas temperature too
high ............................................
67
Table 23
Malfunctions during operation –
Charge air pressure too low ......
67
Table 24
Malfunctions during operation –
Charge air pressure too high ....
68
Table 25
Malfunctions during operation –
Engine performance losses .......
68
Table 26
Malfunction – Turbocharger
pumping .....................................
69
Table 27
Malfunction – Sporadic surge
blows ..........................................
69
Table 28
Malfunctions when stopping –
Runout noises ............................
70
Table 29
Malfunctions when stopping –
Runout time too short.................
70
Table 30
Malfunction of the speed
measurement system
– No
signal or poor signal amplitude ..
71
Table 31
Malfunction of the speed
measurement system
–
Measured speed too high ..........
71
Table 32
Malfunction of the speed
measurement system
–
Measured speed too low ...........
71
Table 33
Swivel lifting eyes .......................
75
Table 34
Ring nuts to be used ..................
76
Table 35
Weights of assemblies ...............
77
Table 36
Gas outlet flange press-off
screws ........................................
80
Table 37
Permissible clearances A and B
87
Table 38
Permitted nozzle ring
compression PD.........................
88
Table 39
Tightening torque (51007) .........
91
Table 40
Tightening torque (79041) .........
93
Table 41
Tightening torque (72011) .........
94
Table 42
Permissible clearances N
and R ..........................................
95
Table 43
Tightening torque (72020) .........
96
Table 44
Tightening torque (51009) .........
97
Table 45
Tightening torques of the screw
fittings .........................................
98
Table 46
Tightening torques for insulation
99
Table 47
Cover plate dimensions [mm] ....
104
Table 48
Customer spare part set 97070 .
109
Table 49
Spare parts list ...........................
111