ABB A170-M Series - Tables

Operation Manual / A170-M.. - A175-M..
Tables
© Copyright 2022 ABB. All rights reserved. HZTL4033_EN Revision K January 2022
Tables
Table1: Definition of pictograms ............................... 9
Table2: Personal protective equipment to be worn
at all times ...................................................................... 13
Table3: Personal protective equipment to be worn
specific to the respective task ................................... 13
Table4: Weight of complete turbocharger unit .... 28
Table5: Foot screws, dimension and strength class..
34
Table6: Foot screws, dimension CE......................... 34
Table7: Foot screws, dimension TE ......................... 34
Table8: Foot screws, number of cup springs ........ 34
Table9: Torque-controlled tightening of the pres-
sure screws .................................................................... 37
Table10: Oil pressure range........................................ 41
Table11: Oil temperature at the inlet....................... 42
Table12: Oil temperature at the outlet.................... 42
Table13: Expected replacement intervals............... 52
Table14: Recommended replacement intervals .... 52
Table15: Tightening torque (81272) ......................... 56
Table16: Tightening torque (81273)......................... 56
Table17: Compressor cleaning parameters ........... 60
Table18: Compressor cleaning parameters ........... 63
Table19: Cleaning parameters Wet cleaning of tur-
bine and nozzle ring..................................................... 69
Table20: Malfunctions when starting – Delayed
start-up .......................................................................... 70
Table21: Malfunctions when starting – Vibrations 70
Table22: Malfunctions when starting – Rubbing of
rotating parts................................................................ 70
Table23: Malfunctions during operation – Lubricat-
ing oil pressure too low................................................ 71
Table24: Malfunctions during operation – Drop in
speed ............................................................................... 71
Table25: Malfunctions during operation – Speed in-
creases ............................................................................ 71
Table26: Malfunctions during operation – Exhaust
gas temperature too high ........................................... 72
Table27: Malfunctions during operation – Charge air
pressure too low............................................................ 72
Table28: Malfunctions during operation – Charge air
pressure too high .......................................................... 73
Table29: Surging of the turbocharger...................... 73
Table30: Malfunctions when stopping – Runout
noises............................................................................... 74
Table31: Malfunctions when stopping – Shortened
runout time ..................................................................... 74
Table32: Malfunction, No speed measurement sig-
nal or poor signal amplitude ....................................... 75
Table33: Malfunction, Measured speed too high ... 75
Table34: Malfunction, Measured speed too low .... 75
Table35: Assembly weights ........................................ 78
Table36: Axial clearance A ........................................... 81
Table37: Tightening torque (56014) ......................... 95
Table38: Tightening torque (57005)......................... 96
Table39: Tightening torque (61069) ......................... 98
Table40: Tightening torque (61059 / 42128) ........ 100
Table41: Tightening torque(86505) ....................... 101
Table42: Inner thread size (25008).......................... 102
Table43: Tightening torque (25013)........................ 103
Table44: Tightening torque (61037) ....................... 104
Table45: Tightening torque, nuts that are difficult
to access (61037) ......................................................... 104
Table46: Tightening torque (61090)....................... 104
Table47: Tightening torque (77015)........................ 105
Table48: Tightening torque(72011)........................ 107
Table49: Axial clearance A......................................... 108
Table50: Tightening torque(72027) ....................... 109
Table51: Tightening torque(72027) ........................ 110
Table52: Tightening torque (56014) ........................ 115
Table53: Tightening torque (61009) ........................ 115
Table54: Tightening torques..................................... 117
Table55: Tightening torques 61009......................... 118
Table56: Locking device tightening torque............ 121
Page 145 / 146Page 145 / 146