ABB XFC G5 - Figure 8-19: Enable Bluetooth

To Next Page

To Previous Page

72 | XSE RI ES G5 | 210602 6MNAA

Figure 8-19: Enable Bluetooth

Select the Communication Setup tab. The Bluetooth interface is unused in the port list.

Figure 8-20: Communication Setup for Bluetooth

Select Bluetooth (Unused).

Select Add New Device/Application. See the figure below.

Main Page

Default Chapter2
- Table of Contents2
List of Figures6
List of Tables9
Additional Information10
Safety11
- Safety Symbol Conventions11
- Potential Safety Hazards for this Equipment12
1 System Description13
- Xseries G5 Enhancements and Backwards Compatibility13
- Embedded Software (Overview)14
- Hardware Overview20
- User Interface Software Description: PCCU3223
- Power Supply Equipment23
- Resistive Temperature Detector (RTD)24
2 Site Planning and Requirements26
- Enclosures26
- Power Requirements26
- Location Specification and Design26
- Wiring Requirements26
- Download PCCU27
  - Install PCCU27
3 Installation28
- Assumptions28
- Required Tools and Materials28
- Unpack and Inspect29
- Pipe Mount Installation29
- Wall Mount Installation30
- Direct-Mount Installation31
- Xrc G531
- Ground Equipment34
- Leak-Test Manifold and Tubing Connections34
- Figure 3-4: 6990 Rack Mount Enclosure34
- Install the RTD35
- Figure 3-6: Typical RTD Installation36
- Wire the RTD to the XFC37
- Install Antenna (for Wireless Functionality)38
- Install the Radio38
4 Install Battery and Charger39
- Install the Battery39
- Install the Solar Panel39
- Figure 4-1: Solar Panel40
5 Wire COMM Ports43
- COMM Port Description43
- Xfc G543
- XRC COMM Pinouts47
- Figure 5-5: XRC RS-232 COMM 147
- Figure 5-6: XRC RS-485 COMM 148
6 Wire I/Os49
- General I/O Description49
- Analog Input (AI) Pinouts51
  - Xfc G5 Ai51
  - Xrc G5 Ai51
- Digital Input and Output (DI/DO) Pinouts XFC DI/DO52
7 Powering the Device54
- Super Capacitor Charging at Boot Time54
- Power-On Sequence54
- Power with Battery and Charger54
  - Connect the Battery (DC Power)55
  - Connect the Charger55
- Power with External Power Supply56
- Figure 7-4: XFC G5 Charger Connection56
- Enable Real Time Clock Backup57
- Figure 7-6: Battery and Switch57
8 Basic Configuration and Startup58
- Setup PCCU for Connection58
  - Figure 8-1: System Setup59
  - G5 or XRC G560
- Change to Expert View60
- Figure 8-3: PCCU32 Date/Time Synchronization Warning60
- Station Setup61
- Change the Default Time and Date Format62
- Initial Measurement Application Setup62
- Figure 8-7: Station Setup Detail62
- Figure 8-8: Flow Measurement Advanced Setup (Gas Orifice)63
- Configure Communication64
- Commission the Device74
9 Configure Security (Recommended)76
- Access Points76
- Communication Interfaces76
  - User-Enabled Services76
  - Open Transmission Control Protocol (TCP) Ports77
- Denial of Service (DOS) Thresholds Rates78
- Security Guidelines78
- Configure Bi-Level Security with Security Switch79
- Figure 9-2: S1 Security Switch80
- Configure Role-Based Access Control (RBAC)81
- Secure the SSH/SFTP Service87
10 Service and Maintenance100
- Preserve Data and Configuration100
- Change the Xseries Clock105
- Remove and Replace Parts106
- Restart the System106
- Remove and Restore Power114
  - Remove Power from the Electronic Board114
  - Reconnect Power to the Electronic Board115
- Adjust the LCD Contrast115
- Xseries Replacement Parts and Procedures116
11 Calibration122
- Measurement Pressure Checks and Calibration122
- Zero Transducer127
  - Static Pressure128
  - Differential Pressure128
- RTD Calibration128
- Table 11-2: RTD Wiring Pinouts129
- Resistance Temperature Detectors (RTD) Bias130
- Analog Input Calibration130
12 Troubleshooting139
- LCD Visual Alarm and Status Codes139
- Failure to Start140
- Screen Locked-Up140
- Remote Communication Failure141
Appendix A Typographical Conventions142
- Table 12-2: Typographical of Conventions142
Appendix B Cyber Security143
Appendix C Compliance144
Contact Us145

ABB XFC G5 - Figure 8-19: Enable Bluetooth

Table of Contents

Other manuals for ABB XFC G5

Related product manuals