What to do if my Abus DVR has no power?
If your Abus DVR has no power, first ensure the mains cable is securely connected to the socket. Then, check that the power switch is turned to the 'ON' position. Finally, verify that the power socket is working by testing it with another device.
Why is there no image on my Abus TVVR45021 DVR?
If there is no image on your Abus DVR, make sure that your screen is set to receive the correct video input mode until you see the recorder's image. Also, check that the video cable is securely connected and that the connected monitor is switched on.
What to do if the remote control for my Abus TVVR45021 is not working?
If the remote control for your Abus DVR isn't working, first replace the batteries, ensuring they are inserted with the correct polarity, and point the remote at the sensor on the device. If that doesn't work, make sure you are within 7 meters of the device and that there are no obstructions blocking the signal. Also, switch off any strong fluorescent lighting nearby.
Why is there no sound on my Abus DVR?
If you're not getting any sound from your Abus DVR, first ensure the audio cables are securely connected. Check that any devices connected via the audio cables are switched on. If the problem persists, the audio connection cable may be damaged and need replacing.
How to fix HDD not working on Abus TVVR45021?
If the HDD in your Abus DVR isn't working, begin by checking that the connection cables are securely connected. If the issue persists, the HDD might be defective or incompatible with the system; in this case, replace it with a recommended HDD.
What to do if recording is not possible on Abus TVVR45021 DVR?
If recording is not possible on your Abus DVR, you may need to install and initialise the HDD.
Why does my Abus DVR suddenly deactivate?
If your Abus DVR suddenly deactivates, it could be due to the temperature inside the device being too high. Clean the device and remove any obstructions from the ventilation area to resolve this.
How to fix USB port not working on Abus TVVR45021 DVR?
If the USB port on your Abus DVR isn't working, the connected device may not be supported. Try connecting a compatible USB medium (USB 2.0). Also, if you're using a USB hub, connect the USB medium directly to the DVR instead.
How to solve network access not possible on Abus TVVR45021?
If network access is not possible on your Abus DVR, first connect the network cable securely. If the issue persists, check the network configuration (DHCP, IP address, etc.) and correct it if necessary.
General| Model | TVVR45021 |
|---|---|
| Hard Drive Support | Yes |
| Hard Drive Bays | 1 |
| Operating System | Embedded Linux |
| Storage Capacity | Up to 6TB |
| Motion Detection | Yes |
| Power Supply | 12V DC |
| Video Outputs | 1 |
| Audio Outputs | 1x RCA |
| Network Interface | Ethernet |
| USB Ports | 2 |
| Video Compression | H.264 |
| Remote Viewing | Yes |
| Operating Temperature | -10°C to 55°C |
Details of controls and buttons on the front panel of the NVR.
Explains all the ports and connectors on the back of the device.
Details of buttons and functions on the provided remote control.
Instructions for connecting cameras, monitors, and other peripherals.
Guidance on initial device setup via the wizard.
Defines the intended purpose and appropriate usage of the device.
Safety precautions related to the device's power source and UPS usage.
Guidelines for selecting a safe and suitable place to install the device.
Warnings and precautions regarding electrical overloading and voltage surges.
Steps and safety checks before operating the device for the first time.
Guides through basic system settings like language and time.
Instructions for configuring the administrator account and password.
Setting the system's date and time for accurate logging.
Configuration of network parameters, including IP addresses and DHCP.
Steps for initializing and managing installed hard disk drives.
Settings for configuring camera recording schedules and types.
Process for adding and configuring network cameras.
Controls available directly on the camera image for quick actions.
Adjusting live view display settings and camera outputs.
Configuring how cameras are displayed on monitors.
Details on using the control panel for playback navigation.
Core device settings including language, time, and display.
Detailed configuration of network parameters for device connectivity.
Physical and logical network setup requirements.
Specific settings for network interface configuration.
Configuration of alarm inputs, outputs, and system responses.
Defining reactions and schedules for alarm events.
Settings for individual cameras, including name, OSD, and image properties.
Settings for motion detection and related actions.
Defining recording times and triggers based on schedules.
Step-by-step instructions for installing a hard disk drive.
Monitoring the health and status of installed HDDs.
Common problems and their potential causes and solutions.
To Next Page
