- 25 -
Step 11 Repeatedly press the SETUP MODE button until display reads "LABEL INPUTS".
Step 12 Press the ALL button to engage the Character Generator. Use the REAR and CENTER buttons to
position the cursor under the letter "T" in "TV/CABLE". Use the LEFT button to move up the alpha-
bet until the letter "L" replaces the letter "T". If you passed the letter "L", pressing of the RIGHT
button will go down the alphabet. Use the CENTER button to advance the cursor one position until
its flashing under the letter "V". Again, use the LEFT button to move up the alphabet until the letter
"A" replaces the letter "V". Continue with this operation until the display reads "LASER DTS 3".
Please note, the last three spaces on the display (blank, blank, 3) cannot be altered.
Step 13 Repeatedly press the INPUT SELECT button until the display reads "VCR 4".
Step 14 Again, repeatedly press the SETUP MODE buton untilthe display reads an A/V Link.
Step 15 Use the VOL UP or VOL DN buttons until the display reads "ANALOG3/V3"
Step 16 Repeatedly press the INPUT SELECT button until the display reads "SATELLITE 5".
Step 17 Again, press the SETUP MODE buton and the display sould read an A/V Link.
Step 18 Use the VOL UP or VOL DN buttons until the display reads "ANALOG4/V4"
Step 19 Repeatedly press the INPUT SELECT button until the display reads "CD PLAYER 6".
Step 20 Again, press the SETUP MODE buton and the display sould read an A/V Link.
Step 21 Use the VOL UP or VOL DN buttons until the display reads "DIGITAL2/V#". The "#" can be any
video number. You may wish to select a video link which you might watch while listening to CD.
Step 22 Repeatedly press the INPUT SELECT button until the display reads "TUNER 7". This Input Label
will be used for the DTS Music and will need to be reset for both an A/V Link and its label.
Step 23 Again, press the SETUP MODE buton and the display sould read an A/V Link.
Step 24 Use the VOL UP or VOL DN buttons until the display reads "MUTI PIN/V1".
Step 25 Repeatedly press the SETUP MODE button until display reads "LABEL INPUTS".
Step 26 Press the ALL button to engage the Character Generator. Use the REAR and CENTER buttons to
position the cursor under the letter "T" in "TUNER". Use the LEFT button to move up the alphabet
until the letter "D" replaces the letter "T". If you passed the letter "D", pressing of the RIGHT button
will go down the alphabet. Use the CENTER button to advance the cursor one position until its
flashing under the letter "U". Again, use the LEFT button to move up the alphabet until the letter "T"
replaces the letter "U". Continue with this operation until the display reads "DTS MUSIC 7".
Step 27 Repeatedly press the INPUT SELECT button until the display reads "MULTIROOM 8". This Input
Label will be used for the TV/CABLE and will need to be reset for both an A/V Link and its label.
Step 28 Repeatedly press the SETUP MODE buton until the display reads an A/V Link.
Step 29 Use the VOL UP or VOL DN buttons until the display reads "ANALOG 2/V2".
Step 30 Repeatedly press the SETUP MODE button until display reads "LABEL INPUTS".
Step 31 Press the ALL button to engage the Character Generator. Use the REAR and CENTER buttons to
position the cursor under the letter "M" in "MULTIROOM". Use the LEFT button to move up the
alphabet until the letter "T" replaces the letter "M". If you passed the letter "T", pressing of the
RIGHT button will go down the alphabet. Use the CENTER button to advance the cursor one
position until its flashing under the letter "U". Again, use the LEFT button to move up the alphabet
until the letter "V" replaces the letter "U". Continue with this operation until the display reads "TV/
CABLE 8".
To Next Page
Loading...
