AERMEC ANK045 HP - Principle of Operation Diagrams

To Next Page

To Previous Page

11_11. 6755532_02



 



 Compressor

HPT High pressure transducer

HPS High pressure switch

 Low pressure switch

 4-way cycle reverse valve

 Coil

 One-way valves

 Orifice

F Dehydrator filter

 Storage liquid

TEV Thermostatic valve

 Plate exchanger

V Fan/s



O 









TEV

compressore

valvola

inversione

BHE

acc

umulo

liquido

pompa

HPSHPT

LPT

VIC

Main Page

Table of Contents4
Description and Choice of Unit6
Available Version6
Configurator7
Cek List8
Principle of Operation Diagrams Cooling9
Hydraulic Circuit (Configurable Version)10
Cooling Circuit10
Frame and Fans10
Hydraulic Circuit Standard10
Water Features10
Safety and Control Components10
Electric Components11
Accessories Compatibility12
Technical Data13
Heating Mode14
Operation Limit14
Cooling Mode14
Performance and Absorption that Differ from the Nominal - Heating Mode15
Ank 030 H (220V-1-60Hz ) Heating Capacity and Input Power15
Ank 045 H (220V-1-60Hz ) Heating Capacity and Input Power16
Ank 050 H (220V-1-60Hz ) Heating Capacity and Input Power17
Ank 030 H (220V-1-60Hz ) Cooling Capacity and Input Power18
Ank 045 H (220V-1-60Hz ) Cooling Capacity and Input Power19
Ank 050 H (220V-1-60Hz ) Cooling Capacity and Input Power20
Ank 030 Hp-Ha (220V-1-60Hz ) Heating Capacity and Input Power21
Ank 045 Hp-Ha (220V-1-60Hz ) Heating Capacity and Input Power22
Ank 050 Ha-Hp (220V-1-60Hz ) Heating Capacity and Input Power23
Ank 030 Ha-Hp (220V-1-60Hz ) Cooling Capacity and Input Power24
Ank 045 Ha-Hp (220V-1-60Hz ) Cooling Capacity and Input Power25
Ank 050 Ha-Hp (220V-1-60Hz ) Cooling Capacity and Input Power26
Pressure Drop27
System Side Exchanger + Piping Pressure Drop27
Filter Pressure Drops27
Useful Static Pressures28
Ethylene Glycol Solutions29
How to Interpret Glycol Curves29
Expansion Vessel Calibration30
Minimum/Maximum of System Water Content30
Recommended Minimum Water Content30
Calibration of Safety and Control Parameters31
Protection Device Calibration31
Sound Data31
Sound Levels31
Control Parameters31
Preservation of the Documentation32
Warnings Regarding Safety and Installation Standards32
General Warnings for the Installer32
Selection and Place of Installation33
Minimum Technical33
Handling Example33
Chydraulic Circuit for Internal and External Ank "H" (Standard)34
Hydraulic Circuits of Principle34
Chydraulic Circuit for Internal and External Ank "Hp35
- Chydraulic Circuit for Internal and External Ank "Hp36
System Example37
Barycentre and Antivibration38
Dimension (MM)39
Antivibration Positioning (MM)39
Hydraulic Connection40
Ank 030-045-050 H40
Ank 030-045-050 Ha40
- Electric Connections41
- Recommended Electric Cable Section41
- Electric Power Connection to the Electrical Mains41
- Auxiliary Connections under the Responsibility of the User/Installer41
- Control and Commissioning42
- Preparation for Commissioning42
- Machine Commissioning42
- Season Changeover42
- Functioning Features43
- Set Point in Cooling Mode43
- Set Point in Heating Mode43
- Compressor Start-Up Delay43
- Circulation Pump43
- Fan Speed Control (Dcpx Accessory)43
- Anti-Freeze Alarm43
- Water Flow Rate Alarm43
Maintenance43
Hydraulic Circuit43
- Extraordinary Maintenance44
Load Procedure44
List of Controls for the Guided Procedure45

AERMEC ANK045 HP - Principle of Operation Diagrams - Cooling

Table of Contents

Related product manuals