How to resolve Port 1-6 Adapter issues on Allen-Bradley PowerFlex 70 Controller?
To resolve issues with the Port 1-6 Adapter on your Allen-Bradley Controller: * Check the communication adapter board for proper connection to the external network. * Check the external wiring to the adapter on the port. * Verify any external network faults.
How to fix IR Volts Range issue on Allen-Bradley PowerFlex 70?
To correct an IR Volts Range issue on your Allen-Bradley Controller, re-enter the motor nameplate data.
How to resolve Auxiliary Input issues on Allen-Bradley Controller?
To resolve issues with the auxiliary input on your Allen-Bradley Controller, check the remote wiring.
How to fix Params Defaulted on Allen-Bradley Controller?
If your Allen-Bradley Controller indicates that parameters have defaulted: * Clear the fault or cycle power to the drive. * Program the drive parameters as needed.
What to do if a non-resettable fault occurs on Allen-Bradley DC Drives?
When a non-resettable fault occurs, it typically indicates a need for drive or motor repair. Before the fault can be cleared, the underlying cause must be addressed. After the repair, the fault will reset upon powering up the drive.
What to do if Allen-Bradley Controller shows Phase U to Grnd?
If your Allen-Bradley Controller is showing a Phase U to Ground fault: * Check the wiring between the drive and the motor. * Inspect the motor for a grounded phase. * If the problem persists, replace the drive.
How to troubleshoot Decel Inhibit on Allen-Bradley PowerFlex 70?
To troubleshoot a Decel Inhibit issue on your Allen-Bradley Controller: * Verify the input voltage is within the drive's specified limits. * Confirm the system ground impedance follows proper grounding techniques. * Disable bus regulation and/or add a dynamic brake resistor and/or extend the deceleration time.
What to do if Allen-Bradley Controller shows Trnsistr OvrTemp?
If your Allen-Bradley Controller displays a Transistor Over Temperature warning: * Check for blocked or dirty heat sink fins. Ensure the ambient temperature hasn't exceeded 40°C (104°F) for IP 20 (NEMA Type 1) installations or 50°C (122°F) for Open type installations. * Inspect the fan's functionality.
How to troubleshoot HW OverCurrent on Allen-Bradley PowerFlex 70?
To troubleshoot a HW OverCurrent issue on your Allen-Bradley Controller, check the programming, look for excess load, verify the DC boost setting, and ensure the DC brake volts are not set too high. Also, investigate other potential causes of excess current.
What to do if Allen-Bradley PowerFlex 70 Controller shows Phase UV Short?
If your Allen-Bradley Controller displays a Phase UV Short error: * Check the motor and drive output terminal wiring for any shorted conditions. * If the problem persists, replace the drive.
General| Input Voltage | 200-240V AC, 380-480V AC, 500-600V AC |
|---|---|
| Frequency Range | 0 - 400 Hz |
| Humidity | 5% to 95% non-condensing |
| Output Voltage | 0 to Input Voltage |
| Control Methods | Sensorless Vector Control |
| Communications | Ethernet/IP, DeviceNet, ControlNet |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overtemperature, Ground Fault |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
| Enclosure Rating | IP20, NEMA Type 1 |
Outlines critical safety information for qualified personnel and product handling.
Provides important safety information regarding the use of output contactors.
Explains the basic parameter view for standard control drives.
Details the basic parameter view specific to enhanced control drives.
Describes advanced parameter views for both standard and enhanced control.
Introduces drive faults and alarms, detailing their types and causes.
Provides steps for acknowledging and clearing drive faults using the HIM or drive controls.
Lists specific fault messages, their causes, and corrective actions.
Lists common drive issues and their recommended solutions for troubleshooting.
Provides detailed electrical and control parameters for drive operation.
Guides users on accessing and modifying drive parameters via the HIM.
Details various methods available for braking or stopping the load.
Explains the drive's programming for protecting the motor from overload conditions.
To Next Page