Do
not
let
the
cable
be
entangled with
surrounding objects
Arrange the wires and cables in accordance
with
the requirements
of
the
manual
to
prevent them
from becoming obstructive while driving. Cables
or
wires
that
obstruct
or
hang
on
the steering
wheel,
shift
lever, brake pedal, etc. are extremely
dangerous.
Do
not
splice cables
Do
not
cut
the
cable insulation
to
supply power
to
other
equipment. Otherwise, the current
carrying capacity
of
the
wire will be exceeded,
resulting
in
fire
or
electric shock.
Do
not
damage the pipe
or
wiring when drilling
When drilling holes
in
the chassis
for
installation,
be careful
not
to
touch, damage
or
obstruct
the
pipes, fuel lines, fuel tanks
or
wires.
If
you
don
't
pay
attention
,
it
can cause fire.
Do
not
use bolts
or
nuts in brakes
or
steering
systems
for
grounding connections
Never
use
bolts
or
nuts used in brakes
or
steering
systems (or any other safety-related systems)
or
fuel tanks
for
installation
or
grounding
connections. The
use
of
such parts will
cause
the
car controller
to
fail, resulting in fire and
so
on.
Do
not
install
on
the
steering wheel
or
gear
lever, etc., which
may
hinder
the
operation
of
the
car
Otherwise,
it
will obstruct the front line
of
sight
or
obstruct moving parts, etc., causing serious
accidents.
& Notice
This symbol indicates
important
instructions.
Failure
to
heed these instructions may result
in
injury
or
major property damage.
When
there is a problem, please stop using
it
immediately
Otherwise,
it
may cause personal injury
or
damage
to
the
product
. Please return this
product
to
an
authorized Alpine dealer
or
the
nearest
Alp
ine service center
for
repair.
Ask professionals
for
wiring and installation
The wiring and installation
of
this product require
professional skills and experience. For safety
reasons, please contact the dealer where you
purchased
lhe
product
for
installation.
Use designated accessories and install securely
Make sure
to
use
only
designated accessories.
!he
use
of
non
-designated parts may cause
internal damage
to
the
device,
or
it
may
not
be
securely installed
in
place. This
can
cause parts
to
loosen and cause danger
or
product failure.
Arrange
the
wires
to
avoid crimping
or
being
squeezed
by
sharp metal edges
The arrangement
of
wires and cables should be
far
away from moving parts (such
as
seat tracks)
or
sharp edges
or
corners. This will avoid
crimping and damage
to
the wires.
If
the wiring
passes
through a metal hole, a rubber gasket
should be used
to
prevent the wire insulation
from
being
cut
by
the edge
of
the metal hole.
Do not install in high humidity
or
dusty locations
Avoid installing
the
device
in
a location
with
high
humidity
or
dust. Moisture
or
dust invades
the device and
can
cause product failure.
& Precautions
Product cleaning
Please use a
dry
soft
cloth
to
clean the product
regularly.
If
the
dirt
is
difficult
to
remove, soak a
soft
cloth
with
water
only
.
Any
other
solvent may
dissolve.
Temperature
Before
turning
on
the machine, please make
sure
that
the temperature in the car is between
+60°C and -20°C.
Maintain
If
you encounter a problem,
do
not
repair
it
yourself. Please return this product
to
an
authorized Alpine dealer
or
the nearest Alpine
service center
for
repair.
Installation location
• This machine cannot be installed in any
of
the
following places:
• Near direct sunlight and heat sources
•
Places
with high humidity and near water sources
• Dusty places
• Locations subject
to
severe vibration
2
-EN
II
To Next Page
Loading...
