Alto SCRUBTEC R 361 User Manual (English)

Questions and Answers:

M
Matthew RogersAug 13, 2025
What to do if the Alto SCRUBTEC R 361 dirty water vacuuming is insufficient?
- J
  Jennifer RubioAug 13, 2025
  If you notice insufficient dirty water vacuuming with your Alto Scrubber, several issues could be the cause. First, check if the recovery water tank is full and empty it if necessary. Second, inspect the vacuum grid for clogs and clean it if needed. Also, ensure the vacuum hose is properly connected to the squeegee. Furthermore, the squeegee itself might be dirty, or the blades could be worn or damaged, requiring cleaning, overturning, or replacement. Finally, verify that the recovery water tank cover is correctly closed and the gasket is in good condition; adjust or replace as needed.
E
Elizabeth AguilarAug 16, 2025
What to do if Alto SCRUBTEC R 361 Scrubber solution flow is insufficient?
- A
  Andrew HarrisAug 16, 2025
  If the solution flow in your Alto Scrubber is insufficient, there are a few things you can check. First, make sure the solution tank is not empty and refill it if needed. Next, inspect the solution filter for dirt and clean it. Lastly, check the tank for any dirt or clogs in the drain hole and clean it out.
O
Olivia CaseAug 20, 2025
Why Alto SCRUBTEC R 361 Scrubber squeegee leaves marks on the floor?
- B
  Brenda SchwartzAug 20, 2025
  If your Alto Scrubber's squeegee is leaving marks on the floor, there could be several reasons. Check for debris under the squeegee blades and clean them. Inspect the squeegee blades for wear, chips, or tears; overturn or replace them if necessary. Also, ensure the squeegee is balanced using the handwheel.
S
Sean WilliamsAug 25, 2025
What to do if Alto SCRUBTEC R 361 brushes don't work and red warning light is on?
- B
  Brian AdamsAug 25, 2025
  If the brushes on your Alto Scrubber aren't working and the red warning light is on, the batteries may be discharged. Charge the batteries.
A
Antonio AllenAug 28, 2025
Why the Alto SCRUBTEC R 361 Scrubber warning lights flash simultaneously?
- Q
  qwiseAug 28, 2025
  If the warning lights on your Alto Scrubber are flashing simultaneously, it indicates that the brush motors are overloaded. To resolve this, use less aggressive brushes suitable for the floor you're cleaning, or avoid using the extra pressure function.
V
vnortonAug 31, 2025
What to do if Alto Scrubber machine does not move?
- T
  Tammy EllisSep 1, 2025
  To address this, turn the Alto Scrubber off, and then turn it back on without pressing the gear pedal.
L
Lori DavisSep 4, 2025
How to fix Alto SCRUBTEC R 361 if the motors do not work?
- J
  James MillerSep 5, 2025
  If the motors on your Alto Scrubber aren't working and no warning light turns on, check the battery connector to ensure it is connected. If it is disconnected, connect it. Also, check if the batteries are discharged and charge them if necessary.
K
Kathy HessSep 8, 2025
What to do if Alto SCRUBTEC R 361 Scrubber switch flashes and brushes don't work at start-up?
- K
  Kent OsbornSep 8, 2025
  If, at start-up, the warning light of the switch on your Alto Scrubber flashes and the brushes don't work, it may be because the machine was turned off without lifting the brush deck. Wait for the deck to lift before turning on the brushes again by pressing the switch.