Version 5.8 5 July 2009
Installation Manual Contents
List of Figures
Figure 2-1: Front Panel Main Components ........................................................................................... 14
Figure 2-2: Rear Panel Main Components ............................................................................................ 15
Figure 2-3: Front- and Rear-Panel Slot Assignment for IPmedia 3000 and Mediant 3000 Simplex with
6310 Blades ........................................................................................................................................... 18
Figure 2-4: Front- and Rear-Panel Slot Assignment for Mediant 3000 HA with 6310 Blades ............... 19
Figure 2-5: Front- and Rear-Panel Slot Assignment for Mediant 3000 Simplex with 8410 Blades ....... 20
Figure 2-6: Front- and Rear-Panel Slot Assignment for Mediant 3000 HA with 8410 Blades ............... 20
Figure 2-7: Fan Tray Unit with Alarm LEDs and ACO Button ............................................................... 21
Figure 2-8: 6310 Blade .......................................................................................................................... 22
Figure 2-9: Components Location on 6310 Blade ................................................................................. 23
Figure 2-10: RTM-6310 Ports Location ................................................................................................. 26
Figure 2-11: RTM-6310 Redundant Rear Transition Module ................................................................ 27
Figure 2-12: 8410 Blade Component Description ................................................................................. 28
Figure 2-13: LED Array Display on 8410 VoP Blade ............................................................................. 30
Figure 2-14: RTM-8410 for 16 Spans (Single SCSI Port) ..................................................................... 32
Figure 2-15: RTM-8410 Redundant for 16 Spans in Slot 4 (Only for Mediant 3000 HA) ...................... 32
Figure 2-16: Two RTM-8410's for 84 Spans (Two SCSI Ports) in Slots 2 and 4 .................................. 33
Figure 2-18: Alarm, Status and Synchronization Blade (SA/M3K) ........................................................ 34
Figure 2-19: Fan Tray Module ............................................................................................................... 36
Figure 2-20: Air Baffle Panel for Unoccupied Front-Panel Slots ........................................................... 36
Figure 2-21: PEM/AC/3K Power Entry Module ...................................................................................... 39
Figure 2-22: PS/AC/3K Power Supply Module ...................................................................................... 40
Figure 2-23: Power Entry Module (PEM) ............................................................................................... 42
Figure 2-24: PS/DC/3K Power Supply Module ...................................................................................... 44
Figure 3-1: Chassis Mounted in 19-inch Rack ....................................................................................... 46
Figure 3-2: Cabling the PSTN Fiber Optic Interface .............................................................................. 50
Figure 3-3: Mini SMB-to-BNC Adaptor Cable (Separate Customer Order) ........................................... 51
Figure 3-4: Cabling the SMB Connector Pair for T3 Interface ............................................................... 51
Figure 3-5: RJ-45 LAN Ethernet Network Port and Connector ............................................................. 52
Figure 3-6: Cabling for LAN Redundancy in Mediant 3000 HA System Only ....................................... 52
Figure 3-7: 100-Pin SCSI Patch Cable Adapter for 16 Spans (Not Supplied)....................................... 54
Figure 3-8: Patch Cable for 42 Spans ................................................................................................... 55
Figure 3-9: 100-Pin SCSI Female Connector on RTM-8410 Blade ...................................................... 56
Figure 3-10: 68-Pin SCSI Female Connector on RTM-8410 Blade ...................................................... 57
Figure 3-11: Cabling PEM Ethernet Ports to Control and OAM Networks ............................................ 58
Figure 3-12: RJ-45 Connector Pinouts .................................................................................................. 58
Figure 3-13: RJ-45 LAN Ethernet Network Port and Connector ........................................................... 60
Figure 3-14: Cabling BITS Trunk Sources on PEM ............................................................................... 61
Figure 3-15: Spring-Cage Alarm Terminal Block Pins ........................................................................... 61
Figure 3-16: Normal Logic Alarm Connection (Redundancy Scheme) ................................................. 62
Figure 3-17: RS-232 Cable Adapter (Supplied) ..................................................................................... 62
Figure 3-18: Connecting AC Power Cord .............................................................................................. 64
Figure 3-19: Power Feed Cable Terminated with Crimp-Connection Type DC Terminal Block ........... 65
Figure 3-20: DC Power Connector with and without Screw-type Terminal Block Connector ................ 66
Figure 4-1: Ejector / Injector Latches on Blades/RTMs ......................................................................... 68
Figure 4-2: Mediant 3000 Page ............................................................................................................. 69
Figure 4-3: Blank Panel for Unoccupied Slots ....................................................................................... 71
Figure 4-4: Removing the Air Filter ........................................................................................................ 74
Figure 4-5: Air Filter ............................................................................................................................... 74
Figure 4-6: Inserting Protective Dust Cover into SFP Cage .................................................................. 75
Figure 4-7: Unlocking the SFP Module .................................................................................................. 76
Figure 4-8: Inserting SFP Module into the Blade's SFP Cage .............................................................. 76
Figure 5-1: Enter Network Password Screen ........................................................................................ 78
Figure 5-2: BootP Client Configuration Screen ..................................................................................... 80
Figure 5-3: Clients for each Blade Added in BootP Utility ..................................................................... 83
Figure 5-4: Multiple Interface Table Page ............................................................................................. 84
To Next Page
Loading...
Need help?
General
