5. Advanced menu
Item
Setti ng
Function
4:3
Regardless of the type of input signal, image is displayed at 4:3
aspect ratio.
USER
Displays the detailed settings.
USER
ENTER
The USE R men u is displayed for the following adjustments.
CLAMP POSITION
1-255 Use to correct so lid white or solid black in the projected im age.
CLAMP WIDTH
1-63 Use to co rrect solid black in the projected image.
VERT. SYNC. AUTO / OFF Use to a djust the image when its motion doesn’t run smoothly. Select
AUTO for normal use.
LPF
ON / OFF
Use to select wh ether or n ot to enable the LPF.
SHUTTER(U) 0-259 (for PHWU -81B) /
0-142 (for PHWX-81B) /
0-126 (for PHX G -91B
Use to adjust the image when nois e appears on the top part of the
image.
SHUTTER(L) 0-259 (for PHWU-81B) /
0-142 (for PHWX-81B) /
0-126 (for PHXG-91B)
Use to adjust the image when noise appears on the b ottom p art of
the image.
SHU TT ER(LS ) 0-3 11 (for P H WU-81B) /
0-192 (for PHWX-81B) /
0-128 (for PHXG-91B)
Use to adjust the image when noise appears on the left half of the
image.
SHUTTER(RS) 0-311 (for P HWU-81B) /
0-192 (for PHWX-81B) /
0-128 (for PHXG-91B)
Use to adjust the im age when noise appears on the right half of the
image.
• Though horizontal strips ma y appear on the enlarged pro
jected ima ge, such sym ptom is not a malfunction.
• When you c hange the horizontal or vertical position to a large extent, noise may ap pear
• The adjustable range of the vertical position v aries depending on the type of the input signal. T hough the ima ge may stay in
the s ame position even w hen the setting value is changed, such symp tom is not a m alfunction.
• When you increase the setting value of O VER SCAN, noise may appear on the screen.
• When 16:9 is selected by SCREEN, you cannot set AS PE CT to 16:9.
• When 4:3 is selected by SCREE N, you cannot set ASPECT to 4:3.
• ASPECT-USER s etting supports the C OM PU TE R1, COM PUT ER2, DV I, and HDMI terminals only. Therefore, you cannot s e-
lec t USER for other terminals.
You can set the IMAGE m enu an d the SIG NAL m enu only wh en the signal is supplied.
5.9 NETWORK menu
Overview
IMAGE INSTALL1 INSTALL2
MULTI-
SCREEN
FEATURE SIGNAL NETWORK INFO
IP CONFIG
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
0. 0. 0. 0
MAC ADDRESS
SAVE SETTINGS
ON
0. 0. 0. 0
OK
0. 0. 0. 0
IMAGE INSTALL1 INSTALL2
MULTI-
SCREEN
FEATURE SIGNAL NETWORK INFO
CONTROL SYSTEM
NETWORK
PASSWORD
NETWORK
CERTIFICATION
PROJECTOR NAME
IP CONFIG
NETWORK RESET
STANDARD
ENTER
ENTER
OK
OFF
NETWORK RESTART
OK
Image 5-19
Item
Setti ng
Function
PROJ EC TO R N A M E
*****...
Set the name to identify the projector. Enter up to 15 c haracters
(alphabets or numeric characters).
R5905597 PHXX SERIES 20/05/2014
51
Downloaded From projector-manual.com Barco Manuals
To Next Page
Loading...
