3 Bentone BF1
General
Table of contents
GENERAL
1. General Information
_____________________________________________________4
Burner servicing schedule ___________________________________________6
Component replacement intervals ________________________________6
Delivery check ____________________________________________________________6
2. Technical data
_____________________________________________________________7
1.1 Dimensions BF1 _______________________________________________________7
2.1.1 Dimensions, flanges _______________________________________7
2.1 Model BF1 FU/FUV 63-16 _________________________________________8
2.1.1 Burner output/ Basic settings _________________________8
2.1.2 Electric Specification ______________________________________8
2.2 Model BF1 KS/KSV 76-24 ________________________________________9
2.2.1 Burner output/ Basic settings _________________________9
2.3 Model BF1 M1V 87-20 ___________________________________________10
2.3.1 Burner output _____________________________________________ 10
2.4 Model BF1 N1V 56-14/BF1 N1 56-14 ______________________11
2.4.1 Burner output _____________________________________________ 11
2.5 Modell BF1 NU1V 60-14 _________________________________________ 12
2.5.1 Burner output _____________________________________________ 12
2.5.2 Basic settings ____________________________________________12
2.6 Modell BF1 R 69-16/BF1 RV 69-16 _________________________13
2.6.1 Burner output _____________________________________________ 13
2.6.2 Basic settings ____________________________________________13
2.7 Recommended nozzles and pressures _____________________ 14
2.8 Nozzle table, 8-15 bar ____________________________________________14
2.8.1 Burner with preheater __________________________________14
2.9 Description ____________________________________________________________15
2.9.1 Components _______________________________________________16
3. Installation
________________________________________________________________17
3.1 Delivery checks ______________________________________________________ 17
3.2 Preparations for installation _____________________________________17
3.3 Oil supply ______________________________________________________________17
3.4 Electrical connection _______________________________________________17
3.5 Choice of nozzle ____________________________________________________17
3.6 Brake plate and airflow setting _________________________________ 17
3.7 Burner installation ___________________________________________________ 18
3.7.1 Hole pattern ________________________________________________ 18
3.7.2 Burner installation ________________________________________ 18
3.7.3 Oil pipes _____________________________________________________18
3.7.4 Electrical connection ____________________________________ 18
4. Basic settings
___________________________________________________________19
4.1 Example of basic setting _________________________________________19
4.1.1 Choice of nozzle __________________________________________19
4.1.2 Basic setting _______________________________________________19
4.1.3 Nozzle assembly adjustment ________________________20
4.1.4 Air intake adjustment ___________________________________20
4.1.5 Method of adjusting air quantity ____________________20
4.1.6 Inlet cone, air adjustment _____________________________20
4.1.7 Air intake rotation ________________________________________21
4.1.8 Air duct ______________________________________________________21
5. Burner servicing
________________________________________________________22
5.1 Warning ________________________________________________________________22
5.1.1 Service position ___________________________________________22
5.1.2 Combustion assembly service ______________________23
5.1.3 Preheater replacement _________________________________ 24
5.1.4 Oil pump replacement __________________________________ 24
5.1.5 Fan motor replacement ________________________________25
5.1.6 Air intake and intake cone service _________________26
5.1.7 Fan wheel checks ________________________________________26
5.1.8 Electrical module _________________________________________28
6. Instructions Pump
____________________________________________________30
6.1 SUNTEC AS _________________________________________________________30
6.1.1 Suction line tables _______________________________________32
6.1.3 Check oil line seals ______________________________________34
6.1.2 Replacement of pump filter ___________________________34
6.1.4 Replacing the solenoid valve (pump) ______________ 35
6.1.5 Replacing the gasket seal (pump) __________________35
6.2 Danfoss BFP 11 and BFP 21 ___________________________________ 36
6.2.1 Technical data _____________________________________________ 36
6.2.2 Components _______________________________________________36
6.2.3 Filter replacement BFP 11 ____________________________36
6.2.4 Filter replacement BFP 21 ____________________________36
6.2.5 Function BFP 11 and BFP 21 _______________________37
6.2.6 LE-S System ______________________________________________38
6.2.7 Purging ______________________________________________________38
6.2.8 Suction pipe tables BFP11 and BFP21 __________39
7. Preheater
__________________________________________________________________40
7.2.1 Function FPHE 5 _________________________________________40
7.2.2 Function FPHE 5-LE ____________________________________40
8. Replacement of electrical components
______________________ 41
9. Electrical equipment LMO1..2..4..
______________________________42
9.1 Wiring diagram ______________________________________________________ 42
9.1.1 Component list____________________________________________43
9.1.2 Function LMO1..2..4.. __________________________________ 43
9.1.3 Technical data _____________________________________________ 44
9.1.4 Colour codes LMO14/24______________________________45
9.1.5 Fault codes LMO14/24 ________________________________45
10. Fault Location
___________________________________________________________46
10.1 Burner will not start ________________________________________________46
10.2 Burner will not start after normal use ________________________46
10.3 Delayed ignition______________________________________________________ 47
10.4 Noise in pump _______________________________________________________ 47
10.5 Pump pressure ______________________________________________________47
11. Log of flue gas analysis
_____________________________________________48
12. Oil burners maintenance instructions
________________________49
13. DECLARATION OF CONFORMITY
_____________________________50
To Next Page
Loading...
