What to do if the user parameters and the factory calibration are lost in Burkert Accessories?
Restart the Burkert Accessories device. If the issue continues, contact the retailer. Also, contact the retailer if the "LIN.LOST" message appears.
What to do if the supply voltage is too low in Burkert Accessories?
If the supply voltage is too low, ensure it's between 18 and 36 V DC. If the issue persists, contact the retailer.
What to do if Burkert Accessories device is not energized?
If the Burkert Accessories device isn't energizing, check the wiring, inspect the installation's fuse and replace it if needed. Also, verify that the installation hasn't been shut down and that the power source is functioning correctly.
Why does the displayed flow rate change very slowly in Burkert Accessories?
If the displayed flow rate changes very slowly, ensure there is fluid in the pipe and try choosing a lower filter.
Why is the displayed flow rate not stable in Burkert Accessories?
If the displayed flow rate is unstable, check that there is fluid in the pipe and consider choosing a higher filter.
What to do if the displayed flow rate is not nil but the flow rate in the pipe is for Burkert Accessories?
If the displayed flow rate isn't nil when the flow rate in the pipe is, verify that the flow rate in the pipe is indeed nil, check for bubbles in the pipe, inspect the chosen filter, and calibrate the flow zero point.
Why does the Burkert Accessories device not properly measure the flow rate?
If the Burkert Accessories device isn't measuring the flow rate accurately, verify that the K factor corresponds to the fitting being used and that the Kw coefficient hasn't been altered. Perform a teach-in procedure to determine the K factor of the fitting.
What to do if Burkert Transmitter programming/testing is unavailable?
General| Model | 8045 |
|---|---|
| Device Type | Transmitter |
| Measurement Principle | Electromagnetic |
| Output Signal | 4-20 mA |
| Material | Stainless steel |
| Lining Material Options | PTFE |
| Electrode Material Options | Stainless Steel, Hastelloy |
| Accuracy | ±0.5% |
| Ambient Temperature Range | -20 to 60 °C |
| Protection Rating | IP65 |
| Certifications | ATEX |
Explains warning symbols and icons used in the manual for safety and information.
Clarifies that the term "device" in this manual refers specifically to the flowmeter type 8045.
Specifies the intended use of the 8045 flowmeter for measuring liquid flow rates.
Describes the flowmeter's components, operation principle, and power supply requirements.
Lists the different versions of the 8045 flowmeter and their key specifications.
Specifies ambient conditions, humidity, altitude, and protection class for device operation.
Details the mechanical components and materials used in the flowmeter construction.
Outlines power supply, current consumption, and output specifications for the device.
Provides critical safety warnings and precautions for installation and commissioning.
Details procedures for mounting the flowmeter onto a pipe, including fitting recommendations.
Explains the electrical wiring connections and procedures for the device.
Important safety warnings related to the device's operation and handling.
Describes the Process and Configuration levels for device interaction and settings.
Explains the function of device buttons and status indicators for user interaction.
Overview of configurable parameters and how to access and adjust them.
How to select the preferred language for the device display interface.
Detailed steps for setting up the 4-20 mA analog output for flow rate measurement.
Setting DO1 to switch based on upper/lower flow rate thresholds for control or alarms.
Setting up the digital input to trigger specific device functions remotely.
Overview of diagnostic tests and calibration procedures available for the device.
Calibrating the 4-20 mA output offset and span for improved measurement accuracy.
Procedure to set the zero point for accurate flow measurements, especially after maintenance.
Critical safety warnings specific to maintenance activities and troubleshooting procedures.
Guidelines for safely cleaning the flow sensor components to maintain performance.
Comprehensive guide to resolving common issues, error messages, and LED indicators.
Troubleshooting steps for issues when the device status LED is off.
Troubleshooting steps for red LED status without explicit error messages.
Troubleshooting steps for orange LED status without explicit error messages.
Lists available spare parts, accessories, and their corresponding order codes.
To Next Page
