G
gail90Jul 31, 2025
What to do if cec DA5 Stereo System has no power?
- MMegan MayJul 31, 2025
If your cec Stereo System has no power, it might be due to a loose AC power cord. Ensure that both ends of the AC power cord are completely connected.
To Next PageTo Next PageWhat to do if cec DA5 Stereo System has no power?
If your cec Stereo System has no power, it might be due to a loose AC power cord. Ensure that both ends of the AC power cord are completely connected.
What to do if my cec DA5 Stereo System has no sound and no sampling frequency is displayed?
If your cec Stereo System shows no sound and no sampling frequency, there could be several reasons: * Check the connection with the player and correct it if necessary. * Ensure the player is turned on and playback has started. * Verify the input on the DA5 and correct it if it's wrong. * Inspect the digital cable for any damage and replace it if broken. * Try turning off and on all the devices to resolve any interference-related issues.
What to do if my cec DA5 Stereo System has no sound but sampling frequency is displayed?
If your cec Stereo System displays a sampling frequency but produces no sound, here's what you can check: * Ensure the connection with the amplifier is correct. * If playback has stopped, restart it. * Increase the volume on the DA5, as it might be too low. * Also, check the volume level on your PC or amplifier and increase it if needed. * Make sure the correct input is selected on the amplifier.
Why is my cec DA5 unresponsive to the remote control?
If your cec Stereo System isn't responding to the remote control, consider these possibilities: * Ensure the DA5 has power and is turned on. * Check if there are batteries in the remote control unit; install them if missing. * If batteries are present, they might be low; replace them with new ones.
How to fix sound skipping on cec DA5?
Sound skipping on your cec Stereo System can often be resolved by addressing these potential issues: * Ensure the player is placed on a stable surface to avoid shocks or vibrations. * Check the disc surface for dirt or smudges and clean it thoroughly.
General| Brand | cec |
|---|---|
| Model | DA5 |
| Category | Stereo System |
| Language | English |
Unplug power before connecting/disconnecting devices. Handle cord with care.
Follow specific power on/off sequence for system components to avoid noise and damage.
Avoid exerting excessive force on the cabinet, switches, knobs, or terminals.
Use an audio rack; avoid direct sunlight, extreme temperatures, or damp locations.
Disconnect the AC power cord from the outlet during thunderstorms.
Allow appliance to acclimate for 1-2 hours when moving between temperature extremes.
Ensure playback sound levels do not disturb others or the neighborhood.
Turns the power ON or OFF. Volume display blinks initially, then shows settings.
Selects digital filter type (FLAT or PULSE). Selected type lights up indicator.
Selects digital input (USB, COAX, TOS, AES). Input name lights up indicator.
Standard 6.3mm headphone output jack. Minimize volume before use.
Adjusts headphones volume clockwise (increase) or counterclockwise (decrease).
Receives signals from remote control. Aim for sensor; avoid obstacles or direct sunlight.
Describes indicators for filter, input, signal format, and sampling frequency/volume.
Controls display brightness in three levels (brighter, off, lighter); resets to default on power-on.
Adjusts analog output level digitally (-99dB to 0dB). Display shows level.
Instructions for connecting to pre-amplifiers and power amplifiers regarding volume settings.
Adjusts headphone volume using both digital control and the front panel knob.
Method to set startup volume to minimum (-99dB) or last memorized volume.
Select FLAT/PULSE filters; FLAT for PCM, PULSE for better time domain response.
XLR (balanced) and RCA (unbalanced) analog outputs. Volume control affects output level.
USB, TOSLINK, COAX, AES/EBU digital inputs with supported formats.
Connects to PC via USB cable. Supports PCM up to 32bit/384kHz and DSD up to 11.2896MHz.
Optical SPDIF input for digital audio players. Supports up to 24bit/192kHz.
Standard SPDIF digital input with RCA connector. Supports up to 24bit/192kHz.
Balanced digital input with XLR connector. Supports up to 24bit/192kHz.
Connect the supplied 3-pin AC power cord to the AC LINE inlet and wall outlet.
Explains functions of DIMMER, D.FILTER, Direct input selectors, INPUT, and D.VOL-UP/DN buttons.
Point towards sensor, avoid blocking, direct sunlight, and low batteries.
Insert two AAA batteries correctly into the compartment.
Replace batteries when remote control range decreases.
Do not mix battery types, remove for long storage, handle leaks carefully, and dispose properly.
Power on sequence, input selection, and playback for COAX, TOS, AES/EBU connections.
Setup and playback for PC music via USB, including driver installation.
Wipe with a soft cloth or diluted neutral cleaning liquid. Avoid harsh chemicals.
Unit requires no periodic maintenance. Contact dealer or service center for issues.
Explains the need for drivers for Windows PC and compatibility.
Provides the CEC home page URL for downloading the specific driver.
Identifies BRAVO-HD as the specialized USB driver for DA5.
Lists required components (drivers) for DSD playback in foobar2000.
Outlines steps to unzip, open, and run the setup.exe for BRAVO-HD driver.
Initiates the BRAVO-HD setup wizard and prompts to proceed.
Choose installation folder and user scope (Everyone/Just me).
Confirms readiness for installation and prompts to proceed.
Notifies about shortcut creation and prompts for system restart to complete installation.
Connects the DA5 unit to the PC via USB cable after the computer restarts.
PC recognizes DA5 as USB Audio; check/set DA5 as output device in sound properties.
Listen to music via analog/headphone outputs after selecting USB input.
Explains that foobar2000 needs ASIO/DSD drivers for DSD playback via DA5.
Details the installation process for the ASIO driver component in foobar2000.
Starts the foobar2000 component installer to add the ASIO driver.
Apply the installed ASIO driver component in foobar2000.
Finalize ASIO driver installation, requiring foobar2000 to restart.
Details the installation process for the ASIO Proxy component in foobar2000.
Launches the ASIO Proxy installer wizard for foobar2000.
Proceeds through the ASIO Proxy setup wizard by clicking "Next".
Choose the destination folder for the ASIO Proxy installation.
Finishes the ASIO Proxy installation and closes the setup wizard.
Details the installation process for the DSD driver component (foo_input_sacd) in foobar2000.
Launches the foobar2000 component installer for the DSD driver.
Starts the foobar2000 component installer to add the DSD driver.
Apply the installed DSD driver component in foobar2000.
Finalize DSD driver installation, requiring foobar2000 to restart.
Guides through configuring foobar2000 for DSD playback.
Opens the Preferences dialog in foobar2000.
Navigates to SACD settings and selects DSD for Output Mode.
Selects the ASIO driver (foo_dsd_asio) for audio output in foobar2000.
Guides configuration of the foo_dsd_asio component for DSD playback.
Sets "BRAVO-HD" as the ASIO driver within the foo_dsd_asio configuration.
Selects "ASIO Native" for DSD Playback Method, crucial for DSD256 compatibility.
Selects ASIO:foo_dsd_asio as the device and clicks OK to complete setup.
Avoid PC interruptions by setting other output; volume control options.
Starts the BRAVO-HD control panel application.
Displays current settings and playback status when DA5 is connected and on.
Allows changing sample rate/bit rate in Windows sharing mode.
Displays current settings and allows changing bit rate/buffer size via foobar2000 ASIO output.
Changes in BRAVO-HD sync with Windows sound settings and vice versa.
Notes potential instability with 352.8/384kHz and recommends lower settings.
Shows PCM playback details (bit rate, sample rate, buffer size) from foobar2000 ASIO.
Advise to set bit rate equal to or higher than the playback file for optimal output.
Warns about potential noise/interruption with small buffer sizes on high-res files.
Shows DSD64 playback status and settings in the BRAVO-HD panel.
Explains fixed bit rate (32 bits) and buffer size (10.0 ms) when using ASIO Native for DSD.
Shows DSD128 playback status and settings in the BRAVO-HD panel.
Shows DSD256 playback status and settings in the BRAVO-HD panel.