Cino eC - Advanced Programming Parameters; Dispensing Delay and Mixer Settings

LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
LM dispensing
if the time you have programmed is other than zero, the N product
motor will be activated at the expiry of the delay time you have
programmed; the delay time is increased or decreased by pressing
keys “4” and “5”;
the rotation time of the product motor can be briefly interrupted
one or two times during the dispensing cycle (0 = no break); (see
also 13.16.);
parameter used in machines complete with a time doser;
if you enable this option after having compressed the ground dose,
the pump will deliver a small water quantity to make it wet, stop
and restart the usual dispensing cycle;
to determine the pump power on time (in I machines) or the
solenoid valve opening time (in E machines) and then the water
quantity it will deliver; you can carry out a “time test” on the set-
point; (see 13.18.);
water will be dispensed in the mixing bowls at the expiry of the
delay time you have programmed;
for I machines only, the water flow in mixing bowls can be
regulated between low, medium, high by pressing keys “4
” and “5”
(see 13.20.);
the rotation time of the mixer fan can be changed by pressing keys
“4” and “5”; if time is equal to zero, the mixer will not rotate; you
can carry out a “time test” on the set-point; (see 13.18.);
if the rotation time is other than zero, the mixer fan will be rotated
at the expiry of this delay time;
the mixer rotation speed can be regulated between low, medium,
high by pressing keys “4” and “5”;
to establish the delay between the second milk and the espresso
coffee dispensing cycle in the “Latte macchiato” selection;
to establish the milk quantity of the second dispensing cycle;
to determine the delay of the second milk dispensing cycle;
to determine the breaks of the second milk dispensing cycle;
to establish the water quantity of the second milk dispensing cycle;
to determine the water quantity delay of the second milk
dispensing cycle;
to establish the mixer rotation time of the second milk dispensing
cycle;
if other than zero, the mixer power on will
be delayed by the time
you have set up;
to determine mixer rotation speed of the second milk dispensing
cycle;
to specify the product canister to be used for the milk dispensing
cycle;
to establish the water to be used for the second milk dispensing
cycle;
to repeat the selection by N times automatically and produce drinks
of remarkable volume (jug);
grinder time
0.0
pre-brewing
0=no N
WATER N time
0= inhib. 0.0
start delay
WATER N 0.0
breaks number
0-1-2 00
start delay
PRODUCT N 0.0
MIXER N
0= inhib. 0.0
start delay
MIXER N 0.0
MIXER speed N
medium
Latte-Macchiato
start coffee 0.0
PRODUCT LM
0= inhib. 0.0
start delay
PRODUCT LM 0.0
breaks number
0-1-2 00
WATER LM time
0= inhib. 0.0
delay water LM
0= inhib. 0.0
MIXER LM
0= disab. 0.0
start delay
MIXER LM 0.0
MIXER LM speed
medium
PRODUCT
MILK LM n: N
Ev virtual
Number= 0
JUG
0=no n:00
cino eC by
MAN1010105 rel. 03 dated 12.02.2014 page no. 29 of 50 page
www.rheavendors.com tel: 0039 02 966 551 fax: 0039 02 96 55 086 e mail: rheavendors@rheavendors.com
rheavendors group's sole property
water flow : N
medium