Cisco IE-4010-16S12P - Where to Go Next

86 pages

To Next Page

To Previous Page

Where to Go Next

You can use the default configuration or use any of the management options described in Management Options,

on page 13 to change the switch settings.

Cisco IE 4010 Switch Hardware Installation Guide

Switch Installation

Where to Go Next

Main Page

Table of Contents3
Product Overview7
Switch Models7
Cable Side8
10/100/1000 Poe/Poe+ Ports (Downlinks)9
Alarms10
Mini USB Port10
SD Flash Memory Card10
Display Mode Button11
Power-Input Terminal11
100/1000 SFP Ports11
Console Ports11
Switch Panel Leds12
Port Leds13
Display Mode Button15
Power-Supply Module Leds16
Alarm Leds16
SD Flash Memory Card LED16
Usb Led17
System LED17
Power-Supply Side17
Power-Supply Side Leds18
Power Supply Features19
Management Options19
Network Configurations20
Switch Installation21
Warnings21
Installation Guidelines23
Verifying Switch Operation23
Installing the Switch23
Rack-Mounting24
Attaching Brackets for 19-Inch Racks24
Attaching Brackets for 19-Inch Racks for IP-30 Compliance (Optional)25
Attaching Brackets for 23-Inch Racks27
Attaching Brackets for ETSI Racks29
Rack-Mounting the Switch30
Wall-Mounting30
Attaching Brackets32
Attaching Brackets for IP-30 Compliance (Optional)33
Wall-Mounting the Switch33
After the Switch Is Mounted on the Wall34
Installing and Removing SFP Modules34
Installing SFP Modules34
Connecting to SFP Modules37
Removing SFP Modules39
Replacing the SD Flash Memory Card39
Connecting Devices to the Ethernet Ports40
Where to Go Next41
Power Supply Installation43
Power-Supply Modules43
Power-Supply Module Installation45
Installation Guidelines45
Installing a Power-Supply Module45
Equipment that You Need46
Grounding the Switch46
Installing the Power-Supply Module in the Switch48
Installing the DC Power Supply in the Switch49
Wiring the Power Source50
Removing the Power-Supply Module54
Troubleshooting55
Diagnosing Problems55
Switch Boot Fast55
Switch Leds55
Switch Connections55
Bad or Damaged Cable56
Ethernet and Fiber-Optic Cables56
Link Status56
10/100/1000 Port Connections56
SFP Module57
Interface Settings57
Ping End Device57
Spanning Tree Loops57
Switch Performance57
Speed, Duplex, and Autonegotiation57
Autonegotiation and Network Interface Cards58
Cabling Distance58
Resetting the Switch58
How to Recover Passwords59
Finding the Switch Serial Number59
Hazardous Location Installation Information61
Hazardous Area Installation Warnings61
North American Hazardous Location Approval63
EMC Environmental Conditions for Products Installed in the European Union64
Hazardous Locations Standards64
Cable and Connectors67
Connector Specifications67
10/100/1000 Ports67
SFP Module Connectors67
Console Port68
Alarm Port69
Cables and Adapters69
SFP Module Cables69
Console Port Adapter Pinouts69
Configuring the Switch with the CLI Setup Program71
Accessing the CLI through Express Setup71
Required Equipment71
Express Setup Procedure72
Accessing the CLI through the Console Port76
RJ-45 Console Port76
USB Console Port77
Installing the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Device Driver78
Uninstalling the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Driver79
Entering the Initial Configuration Information79
IP Settings80
Completing the Setup Program80
Technical Specifications83
Switch Specifications83
Power-Supply Module Specifications85
Alarm Ratings85

Cisco IE-4010-16S12P - Where to Go Next

Table of Contents

Related product manuals