<Sat May 25 02:05:15 2019> Standby arbiter link is currently 12G for F4
module : 6
<Sat May 25 02:05:15 2019> bootvar_copy_cfg_proc: sup migration configuration
started
<Sat May 25 02:05:15 2019> bootvar_copy_cfg_proc:isan_img :bootflash:/n7700-
s3-dk9.8.4.1.gbin ks_img :bootflash:/n7700-s3-kickstart.8.4.1.gbin
<Sat May 25 02:05:18 2019> bootvar_copy_cfg_proc: Kickstart cfg - /isan/bin/
vsh -c "configure terminal ; boot kickstart bootflash:/n7700-s3-
kickstart.8.4.1.gbin "
<Sat May 25 02:05:23 2019> bootvar_copy_cfg_proc: System cfg - /isan/bin/vsh -
c "configure terminal ; boot system bootflash:/n7700-s3-dk9.8.4.1.gbin " <Sat
May 25 02:09:03 2019> bootvar_copy_cfg_proc:command for copy r s -
/isan/bin/vsh -c "copy running-config startup-config vdc-all"
<Sat May 25 02:09:18 2019> procjobcb_job_done: Controller PID : 14342,
sup_migration_procjob_hdl : 14342
<Sat May 25 02:09:18 2019> procjobcb_job_done: sup2_sup3_migration in progress
<Sat May 25 02:09:18 2019> procjobcb_job_done:bootvar config successfully
updated after migration
<Sat May 25 02:09:18 2019> procjobcb_job_done:created migration file
sup2_sup3_migration_standby
<Sat May 25 02:23:28 2019> Read scratchpad_b register 0x96
<Sat May 25 02:31:14 2019> bootvar_handle_mts_msg: migration in progress - 0
<Sat May 25 02:31:30 2019> bootvar_handle_mts_msg: migration in progress - 0
<Sat May 25 02:31:50 2019> bootvar_handle_mts_msg: migration in progress - 0
<Sat May 25 01:55:07 2019> ===============================================
<Sat May 25 01:55:07 2019> Starting Supervisor-2 (N77-SUP2E) migration logging
<Sat May 25 01:55:07 2019> ===============================================
<Sat May 25 01:55:07 2019> System redundancy status data is dumped
successfully <Sat May 25 01:55:07 2019> Active EOBC link is used, continue
migration
<Sat May 25 01:55:07 2019> Deleted EOBC file
/nxos/tmp/eobc_redundant_link_migration.txt successfully
<Sat May 25 01:55:07 2019> Kickstart image file is /bootflash/k3_fin
<Sat May 25 01:55:07 2019> System image file is /bootflash/s3_fin
<Sat May 25 01:55:07 2019> Standby Supervisor-3 (N77-SUP3E) is not preinserted
before starting migration
<Sat May 25 01:55:08 2019> Migration is started by the user
<Sat May 25 01:55:08 2019> system standby manual-boot is invoked and waiting
for Supervisor-3 (N77-SUP3E) to get inserted
<Sat May 25 01:55:08 2019> Migrate file is created
<Sat May 25 01:55:08 2019> Migrate file is created at tftp location
<Sat May 25 01:55:08 2019> F4 arbiter link for standby SUP is : 24
<Sat May 25 01:55:09 2019> Standby arbiter link of F4 card in slot 6 has been
changed to 12G
Viewing Migration Status
<Sat May 25 01:55:09 2019> Standby arbiter link is currently 12G for F4
module : 6
<Sat May 25 01:55:09 2019> Count : 1, Reloading standby
<Sat May 25 01:55:09 2019> subop: 21 Power-management write for migration for
module 3 SUCCESS
<Sat May 25 01:55:09 2019> subop: 21 Power-management read for migration for
module 3 SUCCESS
<Sat May 25 01:55:09 2019> Power-management written value : 0xfe, read_value:
0xfe
<Sat May 25 01:55:09 2019> Waiting for standby Supervisor-3 (N77-SUP3E) to
come online
<Sat May 25 01:55:27 2019> subop: 20 Power-management write for migration for
module 3 SUCCESS
<Sat May 25 01:55:27 2019> subop: 20 Power-management read for migration for
module 3 SUCCESS
<Sat May 25 01:55:27 2019> Power-management written value : 0xfe, read_value:
0xfe
<Sat May 25 01:55:28 2019> subop: 21 Power-management write for migration for
module 3 SUCCESS
Cisco Nexus 7710 Switch Site Preparation and Hardware Installation Guide
103OL-30452-01.
Installing or Replacing Modules, Fan Trays, and Power Supplies
Viewing Migration Status
To Next Page
Loading...
