<Sat May 25 01:55:28 2019> subop: 21 Power-management read for migration for
module 3 SUCCESS
<Sat May 25 01:55:28 2019> Power-management written value : 0xfe, read_value:
0xfe
<Sat May 25 02:02:04 2019> subop: 20 Power-management write for migration for
module 3 SUCCESS
<Sat May 25 02:02:04 2019> subop: 20 Power-management read for migration for
module 3 SUCCESS
<Sat May 25 02:02:04 2019> Power-management written value : 0xfe, read_value:
0xfe
<Sat May 25 02:04:09 2019> Standby has come online !!!
<Sat May 25 02:04:30 2019> ALL_AUTOGRANTS set to 1
<Sat May 25 02:04:30 2019> Standbyfabricloopback test succeeded
<Sat May 25 02:04:30 2019> Standby ready for Switchover, deleting
'/nxos/tmp/migration_log.txt'
<Sat May 25 02:04:30 2019> Saving configuration now
<Sat May 25 02:04:59 2019> Deletion of migration file is successful in
Supervisor-2 (N77-SUP2E)
<Sat May 25 02:04:59 2019> Deletion of tftp migration file is successful in
Supervisor-2 (N77-SUP2E)
<Sat May 25 02:04:59 2019> Copying log file to Standby....
<Sat May 25 02:04:59 2019> Command executed for transferring logfile to other
SUP - ncftpput -u ftpuser -p nbv123 127.1.1.3 /nxos/tmp/
/mnt/plog/migration.log
The sample output when this command is used on the supervisor-2E module is as given below. This output
has the supervisor-2E logs only.
switch# show logging onboard migration status
<Sat May 25 01:55:07 2019> ===============================================
<Sat May 25 01:55:07 2019> Starting Supervisor-2 (N77-SUP2E) migration logging
<Sat May 25 01:55:07 2019> ===============================================
<Sat May 25 01:55:07 2019> System redundancy status data is dumped
successfully <Sat May 25 01:55:07 2019> Active EOBC link is used, continue
migration
<Sat May 25 01:55:07 2019> Deleted EOBC file
/nxos/tmp/eobc_redundant_link_migration.txt successfully
<Sat May 25 01:55:07 2019> Kickstart image file is /bootflash/k3_fin
<Sat May 25 01:55:07 2019> System image file is /bootflash/s3_fin
<Sat May 25 01:55:07 2019> Standby Supervisor-3 (N77-SUP3E) is not pre-inserted
before starting migration
<Sat May 25 01:55:08 2019> Migration is started by the user
<Sat May 25 01:55:08 2019> system standby manual-boot is invoked and waiting
for Supervisor-3 (N77-SUP3E) to get inserted
<Sat May 25 01:55:08 2019> Migrate file is created
<Sat May 25 01:55:08 2019> Migrate file is created at tftp location
<Sat May 25 01:55:08 2019> F4 arbiter link for standby SUP is : 24
<Sat May 25 01:55:09 2019> Standby arbiter link of F4 card in slot 6 has been
changed to 12G
<Sat May 25 01:55:09 2019> Standby arbiter link is currently 12G for F4
module : 6
<Sat May 25 01:55:09 2019> Count : 1, Reloading standby
<Sat May 25 01:55:09 2019> subop: 21 Power-management write for migration for
module 3 SUCCESS
<Sat May 25 01:55:09 2019> subop: 21 Power-management read for migration for
module 3 SUCCESS
<Sat May 25 01:55:09 2019> Power-management written value : 0xfe, read_value:
0xfe
<Sat May 25 01:55:09 2019> Waiting for standby Supervisor-3 (N77-SUP3E) to come
online
<Sat May 25 01:55:27 2019> subop: 20 Power-management write for migration for
module 3 SUCCESS
<Sat May 25 01:55:27 2019> subop: 20 Power-management read for migration for
module 3 SUCCESS
Cisco Nexus 7710 Switch Site Preparation and Hardware Installation Guide
OL-30452-01.104
Installing or Replacing Modules, Fan Trays, and Power Supplies
Viewing Migration Status
To Next Page
Loading...
